Actual Updated Cisco 350-801 CLCOR Exam Dumps

dumps2022-04-13T02:09:52+00:00

New updated Cisco 350-801 CLCOR exam dumps are available. Passing this CCNP collaboration core exam will be easy for each 350-801 candidate. It will be a good news for those Cisco candidates. Free updated Cisco CCNP Collaboration 350-801 CLCOR exam dumps are below.

Page 1 of 10

1. A user reports that when receiving an inbound call on their IP Phone from the PSTN they are unable to transfer this call to another PSTN number.

What is the reason for this failure?

The incoming calling search space of the SIP trunk does not include the partition of the line in the IP phone

The gateway is configured with the wrong device pool

The service parameter related to Offset to Offnet Call Transfer is set to TRUE

The IP phone is configured with the wrong region

2. Refer to the exhibit.

An engineer is troubleshooting a codec negotiation issue where both endpoints that are involved in the call support the codecs listed in the exhibit.

Which audio codec is selected il a call between two endpoints in Region 1 is placed?

711u

722

729

711a

3. A remote office has a less-than-optimal WAN connection end experiences packed loss, delay, and jitter.

Which VoIP codec should be used in this situation?

722.1

711alaw

iLBC

729A

4. AN engineer is implementing toll fraud prevention for incoming calls cluster-wide on cisco UCM.

What is the first step to configure this feature?

Set service parameter 'Block OffNet to OffNet Transfer' to False

Configure blocking for inbound calls based on caller I

Set service parameter "System Remote Access Blocked Numbers' to True

Set service parameter 'Block OffNet To OffNet Transfer' to True

5. Configuration of DNS is required to achieve a fully functional Cisco UCM system Cisco UCM uses DNS to resolve fully qualified domain names to IP addresses for which destinations?

Application server name

Primary TFTP Server for option 150

Cisco Unified Communications Manager Name

Sip trunk

6. An administrator is integrating a Cisco Unity Express module to a Cisco UCME system A test call is placed to the Cisco Unity Express pilot number, but the administrator receives a busy signal.

The dial-peer is configured as follows:

How is this issue resolved?

The dial-peer needs to be reconfigured to support the

711 voice codec.

The dial-peer needs to be reconfigured to support vad.

The destination pattern needs to be changed to match the dialed number of 4100.

The dial-peer needs to be reconfigured to support H 323 instead of SI

7. Which endpoint feature is supported using Mobile and Remote Access through Cisco Expressway?

SSO

323 registration proxy to Cisco Unified Communications Manager

MGCP gateway registration

SRST

8. Which characteristic of distributed class-based weighted fair queueing addresses jitter prevention?

lt provides additional granularity by allowing a user to create classes

It minimizes jitter by implementing a priority queue for voice traffic

It uses a priority queue for voice traffic to avoid jitter

It provides additional granularity by allowing a user to define custom classes

9. Which statement describes the outcome when the trust boundary is defined at the Cisco IP phone?

Packets or Ethernet frames are not remarked by the IP phone.

Packets or Ethernet frames are remarked at the distribution layer switch.

Packets of Ethernet frames are remarked at the access layer switch.

Packets of Ethernet frames are not remarked at the access layer switch.

10. Refer to the exhibit.

The SOP offer/answer has been completed successfully but there is no DTMF when users press keys.

What is the cause of the issue?

DTMF was negotiated properly in these messages.

Payload type 110 was negotiated rather than type 101.

729 rather than

711ulaw was negotiated.

DTMF was not negotiated on the call.

Page 2 of 10

11. A Cisco Telepresence SX80 suddenly has issues displaying main video to a display over HDMI.

Which command can you use from the SX80 admin CLI to check the video output status to the monitor?

xStatus HDMI Output

xStatus video Output

xconfiguration video Output

xcommand video status

12. Refer to the exhibit.

An engineer is troubleshooting this video conference issue:

A video call between a Cisco 9971 in Region1 and another Cisco 9971 in Region1 works.

As soon as the Cisco 9971 in Region1 conferences in a Cisco 8945 in Region2, the Region1 endpoint cannot see the Region2 endpoint video.

What is the cause of this issue?

Cisco 8945 does not have a camera connected.

Maximum Audio Bit Rate must be increased.

Maximum Session Bit Rate for Video Calls is too low.

Maximum Session Bit Rate for Immersive Video Calls is too low.

13. Refer to the exhibit.

Unanswered calls do not reach the voicemail associated with the phones Instead, callers receive the default greeting.

Which action fixes the configuration?

Reboot Cisco Unity Connection

Review the conversation manager logs on Cisco Unity Connection

Check the box "Redirecting Diversion Header Delivery - Outbound", then reset the trunk

Check the box "Redirecting Diversion Header Delivery - Outbound"

14. What are two characteristics of priority queueing? (Choose two.)

It guarantees bandwidth for user-defined traffic classes.

It applies strict priority to user-defined traffic classes.

It allocates an equal share of bandwidth to each flow.

It places traffic Into one of four queues.

It ensures that critical traffic queues are serviced first.

15. An engineer with troubleshoots poor voice quality on multiple calls. After looking at packet captures, the engineer notices high levels of jitter.

Which two areas does the engineer check to prevent jitter? (Choose two.)

Voice packets are classified and marked.

All devices use wired connections instead of wireless connections.

The network meets bandwidth requirements.

Cisco UBE manages voice traffic, not data traffic.

MTP is enable on the sip trunk to cisco Unified Border Element.

16. An engineer is configuring a BOT device for a Jabber user in Cisco Unified Communication Manager.

Which phone type must be selected?

Cisco Dual Mode for iPhone

Cisco Dual Mode for Android

third-party SIP device

Cisco Unified Client Services Framework

17. Refer to the exhibit.

What is the result of applying these two rules to a voice translation-profile for use with an ISDT1 PRI on a Cisco Voice gateway?

The ISDN Type is modified to the administrators defined value.

The ISDN Plan is modified to the administrators defined value.

The leading Plus is stripped from the numeric phone number.

Any Zero is stripped from the numeric phone number.

18. An engineer must configure a cisco ISR 4000 as an MGCP gateway to download its MGCP-specific configuration from cisco UCM.

Which Cisco IOS configuration snippet accomplishes this task?

Option A

Option B

Option C

Option D

19. How can an administrator stop Cisco Unified Communications Manager from advertising the OPUS codec for recording enabled devices?

In CUCM Service Parameters set “Opus codec Enables” to “Enabled for all devices Except Recording-Enabled devices.

Go to the phone’s configuration page and set “Advertise OPUS Codec” to be “false”

Router recorded calls through Cisco Unified Border Element because it does not support OPU

Integrate the Cisco Unified CM with a recording solution that does not support OPU

20. An engineer with ID012345678 must build an international dial plan in Cisco Unified Communications Manager.

Which action should be taken when building a variable -length route pattern?

Configure single route pattern for international calls

Reduce the T302 timer to less than 4 seconds

Create a second route pattern followed by the # wildcard

Set up all international route pattern to 0.1

Page 3 of 10

21. When a call is delivered to a gateway, the calling and called party number must be adapted to the PSTN service requirements of the trunk group. If a call is destined locally, the + sign and the explicit country code must be replaced with a national prefix. For the same city or region, the local area code must be replaced by a local prefix as applicable. Assuming that a Cisco UCM has a SIP trunk to a New York gateway (area code 917), which two combinations of solutions localize the calling and called party for a New York phone user? (Choose two.)

Configure the gateway to translate the calling number and apply it to the dial peer. Combine it with a translation profile for called numbers. ! voice translation-rule 1 rule 1 /^1917/ // rule 2 /^ [+]1917/ // ! voice translation-profile strip+1 translate calling 1 !

Configure two calling party transformation patterns: +1917.CCCCCC, strip pre-dot, numbering type: subscriber +!, strip pre-dot, numbering type: national

Configure two called party transformation patterns: +1917.XXXXXXX, strip pre-dot, numbering type: subscriber +1.!, strip pre-dot, numbering type: national

Configure the gateway to translate called numbers and apply it to the dial peer. Combine it with a translation profile for calling numbers. ! voice translation-rule 1 rule 1 /^1917!/ // rule 2 /^[+]1917!/ // ! voice translation-profile strip+1 translate called 1 !

Configure two calling party transformation patterns: +1917.XXXXXXX, strip pre-dot, numbering type: subscriber +1.!, strip pre-dot, numbering type: national

22. When a user dials a number with a phone that is registered to the Cisco Unified Communications Manager, what is the default timeout before the number is sent?

3 seconds

15 seconds

10 seconds

5 seconds

23. An administrator recently upgraded a Cisco Webex DX80 through its web interface but discovered the next morning that the unit had reverted to its previous version.

What must the administrator do to prevent this from happening again?

Confirm the phone load name in the phone configuration.

Set the prepare cluster for rollback to pre-8.0 enterprise parameter to true.

Assign a universal device template to the phone.

Assign a phone security profile with secure SI

24. Which description of the Mobile and Remote Access feature is true?

Collaboration Edge feature that enables remote individuals to perform international calls from Jabber with a VPN connection

Collaboration Edge feature that enables remote individual to access enterprise collaboration services via Jabber with the use of a VPN connection

Collaboration Edge feature that enables remote individuals to access enterprise collaboration services via Jabber without the use of a VPN connection

Collaboration Edge feature that enables remote individuals to access all enterprise collaboration services using a PC within the corporate environment

25. A Cisco UCM administrator wants to enable the Self-Provisioning feature for end users.

Which two prerequisites must be met first? (Choose two.)

Cisco Extended Functions service must be running

End users must have a secondary extension

End users must belong to Standard CCM Admin Users group the Standard CCM End Users group and the Standard CCM Self-Provisioning group

End users must have a primary extension

End users must be associated to a user profile or feature group template that includes a universal line template and universal device template

26. User A Calls user. The call gets connected, but the quality is bed.

What are two reasons for this issue? (Choose two)

Incorrect partition

No region relationship

Network congestion

Incorrect QoS

Incompatible codec

27. Which description of the function of call handlers in Cisco Unity Connection is true?

They control outgoing calls by allowing you to specify the numbers that Cisco Unity Connection can dial to transfer calls, notify users of massages, and delivery faxes.

They collect information from callers by playing a series of questions and recording the answers.

They answer calls, take message, and provide menus of options.

They provide access to a corporate directory by playing an audio list that users and outside callers users and leave messages.

28. Based on the provided guidance a cisco voice engineer must design media resource management for the customer what is the method that needs to be followed?

configure the hardware transcoder on the hub location router

configure the hardware transcoder on the site A router

configure the hardware transcoder on the site B router.

configure the software transcoder on Cisco UCM to support voice calls to and from both remote sites

29. Which destination does cisco UCM use DNS to resolve fully qualified domain names to IP addresses?

Cisco UCM Name

primary TFTP server for option 150

SIP trunk

application server name

30. Refer to the exhibit.

A collaboration engineer needs to replace the original, single NTP server that was configured during the initial install of a Cisco UCM server.

What is the first step to accomplish this task?

Restart the NTP service on Cisco UC

Enable NTP authentication for the new NTP server on Cisco UC

Stop the NTP service on Cisco UC

Delete the original NTP server from Cisco UCM

Page 4 of 10

31. An administrator must configure the local route group feature on cisco UCM.

Which step will enable this feature?

For each route list configure a route group to use as a Local Route Group.

For each route pattern, select the Local Route Group as the destination.

For each route group, check the box for the Local Route Group feature.

For each device pool. configure a route group to use as a Local Route Group for that device pool

32. What are two differences between media flow-around and media flow-through on cisco unified Border element? (Choose two.)

When using media flow-through, the call signaling and media are passed through the Cisco Unified Border Element

When using media flow-through, the call signaling goes through the Cisco Unified Border Element, but media is not passed through it.

When using media flow-around. the call signaling goes through the Cisco Unified Border Element, but media is not passed through it

When using media flow-around, both call signaling and media do not go through the Cisco Unified Border Element

When using media flow-through, call signaling goes through the Cisco Unified Border Element but media does not

33. Calls are being delivered to the end user in the globalized format. Where does an engineer configure the calling number into a localized format?

gateway

route pattern

IP phone

service parameters

34. When configuring Cisco Unified Communications Manager, which configuration enables phones to automatically register to a Cisco Unified Communications publisher when the connection to the subscriber is lost?

Cisco Unified CM Group

Device Pool

SRST

Route Group

35. An administrator would like to set several Cisco Jabber configuration parameters to only apply to mobile clients (iOS and Android).

How does the administrator accomplish this with Cisco Jabber 12.9 and Cisco UCM 12.5?

Assign the desired configuration file to "Mobile" Jabber Client Configuration in the Service Profile.

Deploy jabber-config-user.xml on iOS and Android devices.

Upload the jabber-config.enc file to TFTP

Create a user profile in Jabber Policies.

36. Which call routing pattern is used for phone numbers that are in the E.164 format?

/+.! Route Pattern

+.! Route pattern

+.! Translation pattern

+1. [2-9]XX[2-9]XXXXXXX called Party Transformation pattern

37. Which DHCP option must be set up for new phones to obtain the TFTP server IP address?

Option 66

Option 15

Option 120

Option 6

38. What is an indicator of network congestion in VoIP communications?

jitter increase due to variable delay

video loss due to video frame corruption

gaps in the voice due to packet loss

discards in the interface of routers and switches

39. What is a capability of Cisco Expressway?

It provides access to on-premises Cisco Unified Communications infrastructure for remote endpoints

It has remote endpoint enrollment with Certificate Authority Proxy Function

It functions as an analog telephony adapter

It gives directory access for remote users via Cisco Directory Integration

40. A customer wants to deploy Cisco Jabber Phone Mode with contacts.

Which two configurations are needed to accomplish this goal? (Choose two)

Add the Application Client Users role to the Cisco UCM end users.

Remove the IM and Presence servers from the Cisco UCM service profile.

Disable Instant Messaging on IM and Presence.

Import Contacts.xml into Jabber.

Enable Cisco UCM end-users for IM and Presence.

Page 5 of 10

41. What is the maximum DNS SRV entries that should be defined in the SIP Trunk destination address field in Cisco UCM?

42. An administrator is in the process of moving cisco unity connection mailboxes between mailbox stores the administrator notices that some mailboxes have active message waiting indicators what

happens to these mailboxes when they are moved?

The move will fall If MWI status Is active.

Moving the mailboxes from one store to another falls If MWI Is turned on.

If source and target mailbox store are not disabled. MWI status is not retained.

The MWI status is retained after a mailbox is moved from one store to another.

43. Refer to the exhibit.

An engineer must modify the existing QoS policy-map statement to implement LLQ for voice traffic.

Which change must the engineer make in the configuration?

bandwidth 170 to LLQ 170

bandwidth 170 to priority 170

bandwidth 170 to reserve 170

bandwidth 170 to percent 170

44. Refer to the Exhibit.

Which command is required to allow this media resource to handle Video Media streams?

maximum sessions hardware 50

video codec h264

codec pass-through

associate application Cisco Unified Border Element

45. How is bandwidth allocated to traffic flows in a flow-based WFQ solution?

Each type of traffic flow has equal bandwidth.

Bandwidth is divided among traffic flows. Voice has priority.

Voice has priority and the other types of traffic share the remaining bandwidth

All the bandwidth is divided based on the QoS marking of the packets.

46. An engineer must configure a route pattern that can route all + E.164 globalized international numbers for the dial plans of all countries.

Which cisco UCM configuration accomplishes this task?

Option A

Option B

Option C

Option D

47. What is required when deploying co-resident VMs by using Cisco UCM?

Provide a guaranteed bandwidth of 10 Mbps.

Ensure that applications will perform Qo

Avoid hardware oversubscription.

Deploy the VMs to a server running Cisco UC

48. The IP phones at a customer site do not pick an IP address from the DHCP. An engineer must temporarily disable LLDP on all ports of the switch to leave only CDP.

Which two commands accomplish this task? (Choose two.)

Switch(config)# no lldp transmit

Switch# configure terminal

Switch# copy running-config startup-config

Switch(config)# no lldp run

Switch(config)# interface GigabitEthernet1/0/1

49. Users want their mobile phones to be able to access their cisco unity connection mailboxes with only having to enter their voicemail pin at the login prompt calling pilot number where should an engineer configure this feature?

message settings

greetings

alternate extensions

transfer rules

50. Which two configuration elements are part of the Cisco Unified Communications Manager toll-fraud prevention? (Choose two.)

SIP trunk security profile.

Partition

Calling search space

SUBSCRIBE calling search space

Feature control policy

Page 6 of 10

51. Which two DNS records must be created to configure Service Discovery for on-premises Jabber? (Choose two.)

_cuplogin._tcp.cisco.com pointing to a record of IM&P

_cisco-uds._tcp.cisco.com pointing to a record of Cisco Unified CM

_cuplogin._tls.cisco.com pointing to the IP address of IM&P

_cisco-uds._tls.cisco.com pointing to the IP address of Cisco Unified Communications manager

_xmpp._tls.cisco.com pointing to a record of IM&P

52. Callers from a branch report getting busy tones intermittently when trying to reach colleagues in other office branches during peak hours An engineer collects Cisco CallManager service traces to examine the situation.

The traces show:

What should be fixed to resolve the issue?

codec configuration

region configuration

class of service configuration

geolocation configuration

53. An administrator configures the voicemail feature in a Cisco collaboration deployment. The user mailboxes must be configured when the Cisco Unity Connection server is configured.

Which action accomplishes this task?

Configure an SCCP integration with Cisco UC

Configure a SIP integration with Cisco UCM to sync users.

Configure an AXL server to access the Cisco UCM users.

Configure an active directory to sync the users who will have a voicemail box.

54. A Cisco Unity Connection Administrator must set a voice mailbox so that is can be accessed form a secondary device.

Which configuration on the voice mailbox makes this change?

Mobile User

Alternate Names

Attempt Forward routing rule

Alternate Extensions

55. What is the element of Cisco collaboration infrastructure that allows Jabber clients outside of the network to register in Cisco Unified communications Manager and use its resources?

Cisco Expressway

Cisco prime collaboration provisioning server

Cisco Unified Border Element

Cisco IM and Presence node

56. Refer to the exhibit.

Cisco-350-80122_1

Which outgoing m-line SDP is sent to Cisco UCM after matching the appropriate dial peers via Cisco Unified Border Element?

A)

Option A

Option B

Option C

Option D

57. What dialed number match this cisco UCM route pattern?

1[23]XX

1200 through 1399 only

1230 through 1239 only

12300 through 12399 only

1200 through 1300 only

58. Which two features of Cisco Prime Collaboration Assurance require advanced licensing

g? (Choose two.)

real time alarm browse

multicluster support

call quality monitoring

email notifications

customizable events

59. What are the last two bits of a DS field in DiffServe Byte used for?

AFxy

ECN

INC

RMI

60. An administrator is asked to implement toll fraud prevention in Cisco UCM, specifically to restrict off-net to off-net call transfers How is this implemented?

Implement time-of-day routing.

Use the correct route filters.

Set the appropriate service parameter

Enforce ad-hoc conference restrictions

Page 7 of 10

61. An administrator configured SIP route patterns cisco com and uc(5-7] cisco 1 com in Cisco UCM A route pattern must be added for ucce2.cisco1.com.

Which two patterns complete the configuration*? (Choose two.)

Option A

Option B

Option C

Option D

Option E

62. What is the major difference between the two possible Cisco IM and presence high-availability modes?

Balanced mode provides user load balancing and user failover only for manually generated failovers. Active/standby made provides an unconfigured standby node in the event of an outage, but it does not provide load balancing.

Balanced mode provides user load balancing and user failover in the event of an outage. Active/standby mode provides an always on standby node in the event of an outage, but it does not provide load balancing.

Balanced mode does not provide user load balancing, but it provides user failover in the event of an outage. Active/standby mode provides an always on standby node in the event of an outage, but is does not provide load balancing.

Balanced mode provides user load failover in the event of an outage. Active/standby mode provides an always on standby node in the event of an outage, and is also provides load balancing.

63. Which configuration step is necessary for a Cisco SIP phone to synchronize its time with a specific source?

Change the Time Zone from “America/Los_Angeles” to “Etc/GMT+8”.

Add a phone NTP Reference to the date/time Group.

Assign the device to the correct region.

Change the time format from 24-hour to 12-hour.

64. After an administrator installs the Cisco jabber Client, it fails to register with the cisco UCM server.

Which two actions should be taken to troubleshoot this problem? (Choose two.)

Verify the installation of the LMHOST file on the PC

Verify the configuration of the DNS SRV record.

Verify corporate firewall settings for client connections.

Verify Layer 3 connectivity on the gateway.

Reboot the Cisco Unified Border Element Gateway.

65. An engineer wants to manually deploy a Cisco Webex DX80 video endpoint to an end user.

Which type of provisioning can be configured on the endpoint?

CUC

CUBE

CMS

Edge

66. What does average rate limiting allow?

transmits traffic bursts up to the Bc size

more traffic than the CIR to be sent when there is available bandwidth

bandwidth up to the Be size

traffic to burst to the Be size when there is available bandwidth

67. DRAG DROP

Drag and drop the SNMPv3 message types from the left onto the corresponding definitions on the right.

68. Which Cisco Unified communications manager configuration is required for SIP MWI integration?

Select “Redirecting Diversion Header Delivery C Inbound” on the SIP trunk.

Enable “Accept presence subscription” on the SIP trunk security profile.

Select “Redirecting Diversion Header Delivery C outbound” on the SIP trunk.

Enable “Accept unsolicited notification” on the SIP Trunk security profile.

69. A network administrator with ID392116981 has determined that a WAN link between two Cisco UCM clusters supports only 1 Mbps of bandwidth for voice traffic

How many calls does this link support if G.711 as the audio codec is used?

70. An engineer with ID378163512 is designing a new dial plan for a customer that has offices in several countries on four continents around the world. This client also want to integrate with a Microsoft Lync backend,

Which dial plan type does the engineer recommend?

SIP URI

TEHO

323

164

Page 8 of 10

71. Which datastore and protocol is used for saving back-up files within the Disaster Recovery System of Cisco UCM?

remote disk on a CIFS share

remote disk on the SFTP server

local disk on the Cisco UCM server

remote disk on an NFS share

72. An administrator is configuring LDAP for Cisco UCM with Active Directory integration. A customer has requested to use 'ipphone' instead of ‘telephoneNumber ’ as the phone number attribute.

Where does the administrator specify this attribute mapping in Cisco UCM?

LDAP directory custom user fields

LDAP Authentication

LDAP directory user fields

LDAP custom Filter

73. A customer wants a video conference with five Cisco TelePresence IX5000 series system.

Which media resource is necessary in the design to fully utilize the immersive functions?

Software conference bridge on Cisco Unified Communications Manager

Cisco PVDM4-128

Cisco Webex meetings server

Cisco meeting server

74. A customer wants to conduct B2B video calls with a partner using an on-premises conferencing solution.

Which two devices are needed to facilitate this request? (Choose two.)

Expressway-C

MGCP gateway

Cisco Unified Border Element

Cisco TelePresence Management Suite

Expressway-E

75. An engineer configures a SIP trunk for MWI between a Cisco UCM cluster and Cisco Unity Connection. The Cisco UCM cluster fails to receive the SIP notify messages.

Which two SIP trunk settings resolve this issue? (Choose two.)

transmit security status

accept unsolicited notification

allow charging header

accept out-of-band notification

accept out-of-dialog refer

76. Which filed is configured to change the caller ID information on a SIP route pattern?

Calling party Transformation Mask

Route partition

Called party Transformation Mask

Connected Line ID Presentation

77. A DTMF mismatch is occurring between an MGCP gateway registered FXS port and a Cisco Unified communications Manager SIP trunk.

Which media resource can be leveraged to interwork this mismatch?

Media Termination point

Conference Bridge

Annunciator

Trusted relay point

78. Configuration of DNS is required to achieve a fully functional Cisco UCM system.

Cisco UCM uses DNS to resolve fully qualified domain names to IP addresses for which destinations?

323

trunk

AAR

MRA

79. A user reports transfer failures from an IP phone for calls received from a PSTN to another PSTN number.

What is a reason for these failures?

The incoming calling search space of the SIP trunk does not include the partition of the line in the IP phone.

The service parameter related to Offnet to Offnet call Transfer is set to TRU

The IP phone is configured with the Wrong region.

The gateway is configured with the wrong device pool.

80. A customer enters no IP domain lookup on the Cisco IOS XE gateway to suppress the interpreting of invalid commands as hostnames.

Which two commands are needed to restore DNS SRV or A record resolutions? (Choose two.)

ip dhcp excluded-address

ip dhcp-sip

ip dhcp pool

transport preferred none

ip domain lookup

Page 9 of 10

81. An administrator executes the debug isdn q931 command while debugging a failed call. After a test call is placed, the logs return a disconnect cause code of 1.

What is the cause of this problem?

The destination number rejects the call

The destination number is busy

The media resource is unavailable

The dialed number is not assigned to an endpoint

82. Refer to the exhibit.

A customer submits this output, captured on a Cisco IOS router.

Assuming that an MGCP gateway is configured with a ISDN BRI interface, which BRI changes resolve the issue?

interface BRI0/1/1 no ip address isdn switch-type basic-net3 isdn incoming-voice voice isdn send-alerting isdn static-tei 0

interface BRI0/1/0 no ip address isdn switch-type basic-net3 isdn point-to-multipoint-setup isdn incoming-voice voice isdn send-alerting isdn static-tei 0

interface BRI0/1/1 no Ip address isdn switch-type basic-net3 isdn point-to-point-setup isdn incoming-voice voice isdn send-alerting isdn static-tei 0

interface BRI0/1/1 no ip address isdn switch-type basic-net3 isdn point-to-multipoint-setup isdn incoming-voice voice isdn send-alerting isdn static-tei 0

83. Which DiffServ marking is the most likely to drop packets?

AF32

AF12

AF11

AF13

84. Refer to the exhibit.

Which Codec is negotiated?

729

ILBC

711ulaw

728

85. Which type of input is required when configuring a third-party SIP phone?

digest user

serial number

manufacturer

authorization code

86. When setting a new primary DNS server in the Cisco UCM CLI what is required for the change to take affect?

restart of CallManager service

restart of DirSync service

restart of the network service

restart of TFTP service

87. After an engineer runs the utils ntp status command on the Cisco Unified Communications Manager publisher, the stratum value is 16.

Which issue can the Cisco Unified CM cluster experience?

The date/time group an all phones default to the time zone of the engineer.

The cluster loses access to port 124 at the firewall.

Unified CM sends an NTPv4 packet.

Database replication is not synchronized on the Unified CM nodes.

88. An engineer implements a new Cisco UCM based telephony system per these requirements:

• The local Ethernet bandwidth is sized based on the total bandwidth per call

• A G.736 codec is used.

• The bit rate is 64 kbps

• The codec sample interval is 10 ms.

• The voice payload size is 160 bytes per 20 ms.

What should the size of the Ethernet bandwidth be per call?

31.2 kbps

38.4 kbps

55.2 kbps

87.2 kbps

89. What is set when using CoS to mark an Ethernet frame?

IPP bits

802.1p User Priority bits

IP ECN bits

DCSP bits

90. To provide high-quality voice and take advantage of the full voice feature set, which two access layer switches provide support? (Choose two.)

Use multiple egress queues to provide priority queuing of RTP voice packet streams and the ability to classify or reclassify traffic and establish a network trust boundary.

Deploy RSVP to improve VoIP QoS only where it can have a positive impact on quality and functionality where there is limited bandwidth and frequent network congestion.

Map audio and video streams of video calls (AF41 and AF42) to a class-based queue with weighted random early detection.

Use 802. 1Q trunking and 802. 1p for proper treatment of Layer 2 CoS packet marking on ports with phones connected.

Implement IP RTP header compression on the serial interface to reduce the bandwidth required per voice call on point-to-point links.

Page 10 of 10

91. Which Cisco Unity Connection handler plays a greeting that announces the option to dial a user extension by default?

the Goodbye call handler

the Operator call handler

the Directory handler

the Interview handler

92. A Cisco UCM administrator sets up new route patterns to support phones in four different locations, all with local gateways. The administrator wants to use the same route pattern for all four locations.

How must the system be configured to achieve this goal?

Use transforms in the route groups.

Use standard local route groups.

Add a CSS to each local gateway.

Use CSS alternate routing rules.

Actual Updated Cisco 350-801 CLCOR Exam Dumps

Actual Updated Cisco 350-801 CLCOR Exam Dumps

Share this post

Leave a Reply Cancel reply

Related Posts