FlashArray Implementation Specialist Exam Dumps

dumps2025-06-30T10:22:04+08:00

FlashArray Implementation Specialist exam is easy for you to pass. There are 60 multiple choice questions in real FlashArray Implementation Specialist exam, and you have 120 minutes to answer all the questions. We provide the latest FlashArrray Implementation Specialist exam dumps, which can help you pass the test easily. Free FlashArrray Implementation Specialist exam dumps are available below.

Page 1 of 3

1. An Implementation Engineer is performing a capacity consolidation on an X50R3.

Which command is needed for the engineer to determine whether the customer’s FlashArray supports SAS Flash Modules?

puredrive list --total --type controller

purehw list --type controller --all

purehw list --type drive --all

2. On a FlashArray//XR50R2/3 Fibre Channel (FC) array, what is the default type and placement of the PCIe FC card?

2-port in slot 0

2-port in slot 2

4-port in slot 0

3. A data pack has been installed and the puredrive list command shows the drives in “unadmitted” status.

Which command should be used to complete the admission?

puredrive add

puredrive admit

purearray drive admit

4. What is the redundancy of the FlashArray//XL PSUs?

1+1

2+2

3+1

5. Which PCIe slot supports 4-port FC cards on FlashArray//XL?

6. A FlashArray//XR2/3 has an Ethernet mezzanine (EMEZZ), what are the interface names of the ports on the mezzanine?

ETH6, ETH7, ETH8, and ETH9

ETH8, ETH9, ETH10, and ETH11

ETH10, ETH11, ETH12, and ETH13

7. What should an Implementation Engineer do when installing rails in a threaded-hole rack?

Use the positioning studs

Install the rails as is

Make an adjustment to the rack

8. Support requests a powercycle on a newly-installed FlashArray.

What is the correct way to perform this action?

Push the power button on each controller.

Unplug the cable on each power supply.

Run purearray reboot.

9. Before leaving the site after an install, who is required to provide completion sign-off?

Account team

Customer

Support

10. Prior to running the puresetup newarray command, which command should an Installation Engineer run on a new install of an //XR4 array?

pureboot list

cobalt_check.py

purehw list

Page 2 of 3

11. A customer has a FlashArray X20R3 with 22/22 data packs in the chassis at 80% space usage and wishes to swap one of the data packs for a 45TB pack.

What step needs to be taken to facilitate this consolidation?

Send a DirectFlash Shelf without any additional capacity.

Send a DirectFlash Shelf with a 63TB of temporary extra capacity.

Reduce array space usage to allow for the evacuation of the 22TB packs.

12. An Implementation Engineer is onsite to install a new DFM data pack (DP) to CH0.BAY10-CH0.BAY19 of a FlashArray.

After adding the drives to the chassis, which command should the Implementation Engineer run to verify if the new DP is in a wide write group?

find_drive.py

puredb list drives

puredrive list --pack CH0.BAY10

13. What is the rack unit height of a FlashArray//XR2/3?

14. An Implementation Engineer is beginning a controller upgrade.

Which command should be run to stop Purity?

pureadm stop

pureadm stop --secondary

pureadm stop --controller CT0

15. When transforming an array from SAS to NVMe with the Evergeen XFORM upgrade, when should a swing shelf be installed?

When the chassis is populated with two data packs

When there is insufficient free space to evac capacity.

When the array is half populated with Flash Modules

16. The Customer’s Implementation Workbook specifies that the SMTP reply is “outlook.microsoft.com:587”.

What correction should be made for array initialization to be successful?

Provide username and password.

Prefix the URL with “https://”.

Remove the port number.

17. For FlashArray//XL, which 2 PCIe slots should be used for DFS connectivity?

0 and 4

0 and 6

1 and 7

18. After running puredb run giveback --safe command once CT0 has been upgraded, how long should the Implementation Engineer wait before continuing with the controller upgrade?

3 minutes

5 minutes

10 minutes

19. Which command should an Implementation Engineer use to allow Support access to an array?

purearray connect --remoteassist

purearray remoteassist

purearray remoteassist --connect

20. A client needs to upgrade Purity on their FlashArray, but is unable to wait for an available upgrade date from support.

What action should the customer take?

Open a ticket with support, download the latest Purity version, copy to a USB flash drive, and run the pureinstall command on each controller.

Log into the Purity CLI, download the latest Purity version, and run the pureinstall command on each controller.

Go through the Self-Service upgrade portal on Pure1 Manage and upgrade to the latest Purity version.

Page 3 of 3

21. If drives need to be relocated within an array for an XFORM upgrade, when should this be completed?

During the upgrade

After upgrade is completed

The following day

22. A customer would like to consolidate their SAS shelves and wants to evacuate multiple shelves in parallel.

What is a prerequisite for this procedure?

Purity must be upgraded to 6.x

The array chassis must be fully populated with modules.

The array usage percentage must be lower than 60%

23. After an Implementation Engineer installs a new FlashArray and runs health checks, they see that Phonehome and Remote Assist are NOT working correctly.

Which outbound port needs to be open for all management ports (physical and virtual)?

443

123

FlashArray Implementation Specialist Exam Dumps

FlashArray Implementation Specialist Exam Dumps

Share this post

Leave a Reply Cancel reply

Related Posts

Pure Storage FBAP_002 Exam Study Guides

FAAA_005 Pure Storage FlashArray Architect Associate Exam Free Dumps