300-615 DCIT CCNP Data Center Actual Questions

dumps2021-12-09T03:17:09+08:00

Cisco 300-615 DCIT exam actual questions are the best preparation material for you to learn the test. Troubleshooting Cisco Data Center Infrastructure 300-615 DCIT exam is much hot among those Cisco candidates. Cisco candidate has 90 minutes to complete all the questions. The available language is English. The exam price is $300. Free Cisco certification 300-615 DCIT exam actual questions are available below.

Page 1 of 3

1. A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN.

Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

2. An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives the error message "Error: Cannot configure postcard when inband-telemetry is configured."

Which action resolves the issue?

Disable the telemetry feature

Disable the software-telemetry feature

Disable the hardware-telemetry feature

Disable the inband-telemetry feature

3. DRAG DROP

An engineer is troubleshooting issues in Cisco UCS Director.

Drag and drop the possible causes from the left onto the correct issues on the right.

4. Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain.

Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VN

5. Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit.

Which action resolves the issue.

Reconfigure the Drive Type from "Removable" to "Non-Removable"

Insert an SD card into SLOT-2

Configure the RAID that is associated with the card.

Set SLOT-1 Sync Mode to "Auto"

6. An engineer must place a Cisco UCS B-Series Server in a single server pool in Cisco UCS Manager. The engineer creates a qualification policy, but the server is still seen in multiple pools.

Which two actions resolve the issue? (Choose two.)

Select the Server Pool Policy Qualification from the qualification drop-down menu in the Server Pool Policy

Select the Server Pool Policy from the qualification drop-down menu in the Server Pool Policy Qualification

Set the operating system qualifier inside the Server Pool Policy Qualification

Set the number of vNICs qualifier inside the Server Pool Policy.

Set the storage capacity qualifier inside the Server Poo. Policy Qualification.

7. Refer to the exhibit.

The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize.

What is the cause of the issue?

VSAN 1 is suspended.

The SFP is unsupported.

Trunk mode must be activated.

The interface is in an incorrect mode.

8. An engineer is implementing a storage VDC, but fails.

Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

M-Series module

ESSENTIALS license

STORAGE-ENT license

FCoE license

F-Series module

9. Refer to the exhibit.

An engineer is troubleshooting why user1, user2, and user3 from group STORAGE-ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI.

Which action resolves the issue?

Configure the role name to match the group name on Microsoft Active Directory.

Include specific users into MDS role configuration.

Configure SSH logins on Cisco MDS switch.

Integrate Cisco MDS with Microsoft Active Directory.

10. A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?

Clean reload the Leaf-1 switch

Define the new TEP address for Leaf-1

Change the clock offset from low to high between apic 1 and Leaf-1

Modify the ISIS interface peering IP address between apic 1 and Leaf-1

Page 2 of 3

11. A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay.

Which two actions optimize the traffic? (Choose two.)

Disable first-hop redundancy.

Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices.

Filter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch.

Filter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch.

Filter HSRP by using a Layer 2 MAC-list on the OTV edge devices.

12. A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity.

However, after the server is rebooted, the host is not accessible on the network Which action resolves the issue?

Remove all existing vNICs and add them in the desired order.

Build a new service profile with the desired network configuration

Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs

Create a vNIC placement policy to avoid adapter renumbering

13. Refer to the exhibit.

After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A? (Choose two.)

Configure the local vPC role priority to have a lower value than Switch-

Configure the local vPC role priority to have a higher value than Switch-

Disable and then re-enable the vPC peer-keepalive link.

Configure the local vPC role priority to have the same value as Switch-

Disable and then re-enable the vPC peer link.

14. An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks.

Which statement about what occurs when the new uplinks are added is true?

Only new connections use the new uplinks automatically.

Paths must be defined before new connections can use the new uplinks.

All connections must be reset before the new uplinks can be used.

New and existing connections use the new uplinks automatically.

15. An engineer is troubleshooting a fabric discovery failure.

Which two requirements must an engineer verify about switch connectivity to solve the problem? (Choose two.)

A Cisco APIC must be attached to a spine node only.

A Cisco APIC must be attached to leaf nodes.

Spine nodes must connect to other spine nodes.

A Cisco APIC must be dual-attached to two separate spine nodes.

Leaf nodes must connect to spine nodes only.

16. Refer to the exhibit.

A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch.

Which configuration did the engineer neglect to apply in the script for it to function properly?

event cli match ‘configure terminal’

event policy-default count 1 time 100

event syslog occurs 10

action 2.0 event-default

17. Refer to the exhibit.

An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues.

Which action resolves the issue?

Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.

Set the local group number as 300 in the remote data center configuration

Run version 1 and version 2 HSRP on VLAN300 in the local data center.

Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

18. An engineer is troubleshooting a custom AV pair that was created by a client on an external

authentication server to map a read-only role for a specific security domain.

Which AV pair solves the problem?

shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2

shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2

shell=Security_Domain_1/Read_Role_1|Read_Role_2

shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2

19. Refer to the exhibit. An engineer troubleshoots an OSPF neighborship problem between Router R2 and Router R10. Which action resolves the problem?

Change area ID on Router R10

Resolve unicast reply from Router R2

Resolve authentication type on Router R10

Change router ID on Router R10

20. DRAG DROP

Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.

Page 3 of 3

21. A user reports that they cannot reach from a UCS server to an FC Storage array.

Which command is used to test communication between an FCF and a target?

fcroute

traceroute

fcping

ping

22. Refer to the exhibit. An engineer discovered a VFC interface in a down state on a Cisco Nexus Switch. Which action resolves the problem?

Change the cable between the switch and the server

Reset the Cisco Nexus port toward the file server

Update the CNA firmware and driver versions

Modify the fip keepalive message time to 30 seconds

23. An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager.

Which two actions must the engineer attempt to resolve the problem? (Choose two.)

Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.

Apply the UCS Central license to UCS Central.

Place Cisco UCS Manager on the same subnet as Cisco UCS Central.

Allow port 443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

24.

Refer to the exhibits. An engineer is implementing the SAN based on the Cisco MDS 9000 Series Switches. When

operating the environment, the engineer encounters the error shown. Which action resolves the issue?

Copy VSAN 101 to the fabric binding database on the MDS-1 switch

Add the World Wide Name of the neighboring switch to the MDS-1 switch

Configure the port security feature on the MDS-1 switch

Enable VSAN 101 on the peer MDS 2 switch fabric interconnect

25. 1.During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a "No Signal" message from the vKVM and physical connection.

Which set of steps resolves the issue?

1- Disconnect the power cord II- Confirm that all cards are property seated 3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord II - Confirm that all cards are property seated 3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord II - Confirm that all cards are available 3- Connect the power cord and power on the server

1- Disconnect the power cord II - Confirm that all cards are properly seated 3- Connect the power cord

26. DRAG DROP

A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image.

Drag and drop the recovery steps from the left onto the correct order on the right.

27. An engineer troubleshoots a VXLAN EVPN data center. The applications in the data center fail to reach the DNS server that is located at IP 10.10.10.10. The engineer examines the BGP EVPN routing table and notes that the IP prefix route covers the DNS server is missing.

Which action resolve the issue?

Set the IP prefix route to represent [5]:[0]:[0]:[32]:[10.10.10.10]/224 in the routing table.

Configure an IP ARP entry to represent [2]:[0]:[0]:[48]:[0050.569f.1285]:[32]:[10.10.10.10]/272 in the routing table

Set the IP prefix route to represent [2]:[0]:[0]:[48]:[0050.569f.1285]:[0]:[0.0.0.0]/216 in the routing table

Configure an IP ARP entry to represent [4]:[0300.0000.00fc.bd00.0309l[32]:[10.10.10.10]/136,n the routing table

28. Refer to the exhibit.

The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200.

What action resolves the issue?

Reconfigure the initiator and the target to be in the same zones.

Reactivate the zoneset.

Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.

Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

300-615 DCIT CCNP Data Center Actual Questions

300-615 DCIT CCNP Data Center Actual Questions

Share this post

Leave a Reply Cancel reply

Related Posts