350-501 SPCOR Exam Dumps have been Updated

dumps2022-01-10T03:02:41+08:00

Cisco 350-501 SPCOR exam dumps have been updated, which can help you test the knowledge of implementing core service. All the updated Cisco CCNP Service Provider 350-501 SPCOR exam dumps can guarantee you success in the first attempt. Free updated Cisco 350-501 SPCOR exam dumps are below.

Page 1 of 9

1. Refer to the exhibit:

Which effect of this configuration is true?

R1 can support a peer that is configured for LDP SSO/NSF as the peer recovers from an outage

R1 can failover only to a peer that is configured for LDP SSO/NSF

R1 can failover to any peer

R1 can support a graceful restart operation on the peer, even if graceful restart is disabled on the peer

2. Refer to the exhibit:

Which effect of this configuration is true?

it creates a pseudowire class named Cisco

It enables tagging for VLAN 12 on the interface

It enables MPLS on the interface

It enables AToM on interface gigabitethemet1/0

3. An engineer implemented LDP protocol on the ISP network. The engineer must ensure that there are no packet loss issues when IGP and LDP protocols are not synchronized.

Which configuring must the engineer implement so that the IGP routing protocol will wait until LDP convergence is completed?

Disable IP CEF routers running LDP and enable LDP protocol.

Configure MPLS LDP IGP synchronization on the network.

Configure LDP sessions protection on the network.

Disable MPLS LDP IGP synchronization on the network.

4. While implementing TTL security, an engineer issues the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command.

After issuing this command, which BGP packets does the PE accept?

from 2.2.2.2, with a TTL of less than 2

to 2.2.2.2, with a TTL of less than 253

from 2.2.2.2, with a TTL of 253 or more

to 2.2.2.2, with a TTL of 2 or more

5. Refer to the exhibit.

A network engineer must meet these requirements to provide a connects, solution:

✑ The customer connected to Area 2 needs to access the application in Area 1 on the 10.10.10.0/24 subnet

✑ The Customer must not have access to the 20.10 30.0/24 subnet.

✑ The service provider must make sure that the Area 2 routing database limits the number of IP addresses in the routing table

Which two configurations must be implemented to meet the requirements? (Choose two)

Set a tag value of 200 to match the summary address 10.0.0/16 on R2.

Set a tag value of 200 to match the summary address 10.0.0.0/16 on R3.

Apply the route map for tag 200 and leak Level 2 routes into Level 1 Area 2 on R3

Apply the route map for tag 200 and teak Level 2 routes into Level 1 Area 2 on R4.

Set a tag value of 200 to match the summary address 10.0.0./16 on R1.

6. BGP has been implemented on a IOS XR router.

Which configuration sends BGP IPv4 labels to build inter-domain LSPs?

router bgp 65515 address-family ipv4 unicast neighbor 172.16.70.23 send-community extended

router bgp 65515 no bgp default ipv4-unicast

router bgp 65515 address-family ipv4 unicast neighbor 172.16.70.23 send-community

router bgp 65515 neighbor 172.16.70.23 address-family ipv4 labeled-unicast

7. Refer to the exhibit:

When implementing an LDP protocol, an engineer experienced an issue between two directly connected routers and noticed that no LDP neighbor exists for 1.1.1.1.

Which factor should be the reason for this situation?

LDP needs to be enabled on the R2 physical interface

R2 does not see any hellos from R1

LDP needs to be enabled on the R2 loopback interface

R2 sees the wrong type of hellos from R1

8. DRAG DROP

Drag and drop the descriptions from the left onto the corresponding OS types on the right.

9. DRAG DROP

Drag and drop the BGP Best Path Algorithm rules from the left into the corresponding order of importance on the right.

10. Refer to the exhibit:

A network engineer is implementing a BGP protocol.

Which effect of the local-as keyword in this configuration is true?

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 and the VPNv4 address family

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 without additional configuration

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 and the VPNv4 address family

It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 without additional configuration.

Page 2 of 9

11. Refer to the exhibit:

An engineer is preparing to implement data plane security configuration.

Which statement about this configuration is true?

Router 1 drops all traffic with a local-preference set to 150

All traffic is dropped

All traffic to 192.168.1.0/24 is dropped

Router 1 and Router 2 advertise the route to 192.0.2.0/24 to all BGFD peers.

12. What causes multicast traffic to permanently stay on the shared tree and not switch to the source tree?

The SPT threshold is set to infinity.

The RP IP address is configured incorrectly.

The RP announcements are being filtered.

SSM range is being used.

13. Refer to Exhibit.

A network engineer is trying to retrieve SNMP MIBs with RESTCONF on the Cisco switch but fails. End-to-end routing is in place.

Which configuration must the engineer implement on the switch to complete?

netconf-yang cisco-ia snamp-community -string Public

snmp-server community cosco RW

snmp-server community public RO

netconf-yang cisco-Ia snmp-community-string Private

14. Refer to the exhibit.

Router 4 is added to the network and must be in the same area as router 1.

Which NET should the engineer assign?

49.0001.0000.0000.0004.00

49.0111.0000.0000.0001.00

49.0011.0000.0000.0003.00

49.0011.0000.0000.0002.00

15. What is a constraint of Cisco MPLS TE tunnel configurations?

Tunnels cannot span multiple OSPF areas.

With ISIS as an IG

only older-style metrics are used.

Tunnels cannot be configured over IP unnumbered links.

QoS-aware tunneling is not supported.

16. Which statement about segment routing prefix segments is true?

It is linked to a prefix SID that is globally unique within segment routing domain.

It is the longest path to a node.

It is linked to an adjacency SID that is globally unique within the router.

It requires using EIGRP to operate.

17. An engineer is trying to implement BGP in a multihomed architecture.

What must the engineer configure to influence inbound path selection?

A route map with WEIGHT attribute to control the inbound traffic.

An offset list to set the metric for routes received from neighboring autonomous systems.

An access list to identify traffic and enable it on both of the provider-facing interfaces.

A route map with AS_PATH attribute to control the inbound traffic.

18. Which two tasks must an engineer perform when implementing LDP NSF on the network? (Choose two.)

Disable Cisco Express Forwarding.

Enable NSF for EIGR

Enable NSF for the link-state routing protocol that is in use on the network.

Implement direct connections for LDP peers.

Enable NSF for BG

19. Refer to the exhibit.

Which the link aggregation configuration router is running on Cisco IOS XR software, which LACP interface configuration is needed to add the interface to the bundle?

A)

Option A

Option B

Option C

Option D

20. You are writing an RPL script to accept routes only from certain autonomous systems Consider this code.

If you apply this code to BGP filters, which effect does the code have on your router?

denies routes from AS 7070

allows routes from AS 7077

denies routes from AS 7007

allows routes from AS 770

Page 3 of 9

21. Refer to the exhibit:

Which statement describes the effect of this configuration?

It applies a service policy to all interfaces remarking HTTP traffic

It creates an ACL named WEB that filters HTTP traffic.

It matches HTTP traffic for use in a policy map

It modifies the default policy map to allow all HTTP traffic through the router

22. ESTION NO: 75

Refer to the exhibit:

You are configuring an administrative domain implement so that devices can dynamically learn the RP?

SSM

BID1R-PIM

BSR

Auto-RP

23. Which service is a VNF role?

Compute

Network

Firewall

Storage

24. Refer to the exhibit.

An engineer implemented OSPF neighbor relationship on an IOS device.

Which configuration must be applied to get the OR/BOR election removed from interfaces running OSPF?

ip ospf network broadcast on interfaces running OSPF

ip ospf network point-to-point on interfaces running OSPF

ip ospf network multipoint-point on interfaces running OSPF

ip ospf network non-broadcast on n:erfaces running OSPF

25. An engineer is implementing MPLS to monitor within the MPLS domain.

Which must the engineer perform to prevent packets from being forwarded beyond the service provider domain when the LSP is down?

Option A

Option B

Option C

Option D

26. Refer to the exhibit.

R101 is peering with R102 and R103, and R201 is peering with R202 and R203 using iBGP Labeled Unicast address families. The OSPF area 0 border routers are in a full iBGP Labeled Unicast mesh, and VPNv4 routes are exchanged directly between PE routers R101 and R201 through iBGP.

Which address family-level configuration must be applied on ABR R102 on ABR R102 to support a Unified MPLS routing architecture with partitioned IGP domains?

A)

Option A

Option B

Option C

Option D

27. A network operator working for a telecommunication company with an employee Id: 4065 96080 it trying to implement BFD configuration on an existing network of Cisco devices.

Which task must the engineer perform to enable BFD on the interfaces?

Disable Cisco Express Forwarding on the interfaces

Disable SSO on the interfaces

Remove any static routes that point to the interfaces

Remove the log option from any ACLs on the interfaces.

28. A network engineer Is implementing a QoS policy for outbound management traffic classification and marking on a CPE device with these requirements:

• Management protocols must be marked with DSCP AF class 2 w4h low drop probability.

• Monitoring protocols must be marked with DSCP AF class 1 with low drop probability.

• All remaining traffic must be marked with a DSCP value of 0.

Which configuration must the engineer implement to satisfy the requirements?

A)

Option A

Option B

Option C

Option D

29. Refer to the exhibit.

Routers R2 and R3 are Level 1/Level 2 IS-IS routers that redistribute 198 18.x.x/24 prefixes to routers R5 and R6 In the Level 1 area R2 Is to be the preferred router for all redistributed prefixes in the Level 1 area.

Which configuration sets this preference?

Option A

Option B

Option C

Option D

30. ASN 65001 is peering with ASN 65002 to exchange IPv6 BGP routes. All routes that originate in ASN 65001 have a standard community value of 65001:100, and ASN 65002 is allowed to advertise only 2001 :db8:aaaa::/48.

An engineer needs to update the ASN 65001 route-filtering configuration to meet these conditions:

* Looped routes into ASN 65001 and routes that have traversed 10 or more ASNs must be denied.

* Routes accepted into ASN 65001 must be assigned a community value of 65001:200.

Which configuration must the engineer apply to the ASN 65001 border router?

A)

Option A

Option B

Option C

Option D

Option E

Page 4 of 9

31. Which control plane protocol is used between Cisco SD-WAN routers and vSmart controllers?

OTCP

OMP

UDP

BGP

32. Refer to the exhibit:

It the NetFlow configuration is updated to version 9, which additional piece of information can be reported"?

IPv6 flow information

flow sequence numbers

BGP AS information

IPv4 flow information

33. While implementing TTL security, you issue the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command.

After you issue this command, which BGP packets does the PE accept?

from 2.2.2.2, with a TTL ol 253 Of more

from 2.2.2.2, with a TTL of less than 2

to 2.2.2.2, with a TTL of less than 253

to 2.2.2.2, with a TTL of 2 or more

34. Egress PE NAT is being used via a single centralized router to provide Internet access to L3VPN customers.

Which description of the NAT operation is true?

Users m different VRFs cannot share the same outside global IP address

The NAT table contains a field to identify the inside VRF of a translation

Multiple address pools are needed for the same L3VPN because each site has a separate NAT

The different L3VPNs using the Internet access must not have IP overlaps internally

35. Refer to the exhibit.

What does the number 2 mean in the configuration?

It dictates the number of sessions that will be open with the SNMP manager

It represents the version of SNMP running.

It indicates two SNMP managers are able to read and write with the agent using community string ciscotest.

It is the numeric name of the ACL that contains the list of SNMP managers with access to the agent.

36. Refer to the exhibit.

A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network.

Which action causes the solution to fail?

A loopback with a /32 IP address has not been used

OSPF does not work with L2VPN services

The xconnect statement has not been defined

The routing protocol network types are not compatible

37. Which action does the ingress VTEP perform on traffic between EVPN VXLAN overlays?

routing and tunneling when doing symmetric IRB

routing when doing asymmetric IRB

routing and bridging when doing asymmetric IRB

bridging when doing symmetric IRB

38. Which statement about Network Services Orchestrator (NSO) is true?

It is used only in service provider environments

It can be used only with XML coding

It uses YANG modeling language to automate devices

It must use SDN as an overlay for addressing

39. An engineer must extend Layer 2 Between two campus sites connected through an MPLS backbone that encapsulates Layer 2 and Layer 3 data.

Which action must the engineer perform on the routers to accomplish this task?

Configure a EtherChannel for E-LA

Configure a pseudowire for E-LIN

Configure Cisco MPLS TE for use with E-TRE

Configure QoS for MPLS and E-ACCESS

40. Refer to the exhibit.

A network engineer is implementing a standard customer route-policy on ASBR1 with these requirements:

• It must accept only customer-assigned prefixes

• It must preserve customer advertised BGP communities

• It must set the local-preference to 110 for all prefixes

• It must attach the ORIGINATION-PE and LOCAL-CITY communities to all accepted prefixes.

Which route policy must the engineer implement on ASBR1 to satisfy the requirements?

Option A

Option B

Option C

Option D

Page 5 of 9

41. Which three OSPF parameters must match before two devices can establish an OSPF adjacency? (Choose three.)

IP address

interface cost

subnet mask

process ID

hello timer setting

area number

42. Refer to the exhibit.

An engineer is implementing BGP selective prefix suppression. The router must advertise only 10.16.4.0/24,10.16.5.0/24. and summarized route 10.16.0.0/21. and suppress 10.16.6.0/24.

Which configuration must the engineer apply to the router?

A)

Option A

Option B

Option C

Option D

43. Refer to the exhibit.

What reestablishes the OSPF neighbor relationship between Router 1 and Router 2?

authentication is added to the configuration

correct wildcard mask is used on Router 2

OSPF process IDs match

hello intervals match

44. Refer to the exhibit.

The USER mat is connecting an application on an Internet connection in AS 100 is facing these issues:

✑ The USER lost the connection to the application during a failure Between IG and R2.

✑ Router R2 configuration a lost due to a power outage.

✑ The application the USER is connecting to a hosted behind CE2.

What action resolves the issues on R3 and R4 routers?

Set R4 as a route reflector for R3 and CE2

Apply high Local Preference on R3 toward R1

Set R3 as a route reflector for R4 and CE1

Apply low Local Preference on R4 toward R2.

45. What are the two uses of the YANG data modeling language? (Choose two.)

It is used to access a device by HTT

It Is used to model the configuration used by NETCONF operations.

It is used to shape state data of network elements.

It Is used to replace RESTCONF as a mechanism to install and manipulate configuration.

It is used to replace the OSI model for troubleshooting.

46. Refer to the exhibit.

An engineer is securing a customer's network.

Which command completes this configuration and the engineer must use to prevent a DoS attack?

neighbor ebgp-multihop

ebgp-multihop

ttl-security

neighbor-ttl-security

47. Which protocol does a Cisco MPLS TE tunnel use to maintain paths within the core?

RSVP

VTP

STP

RPF

48. DRAG DROP

Drag and drop the functions from the left onto the correct Path Computation Element

Protocol roles on the right

49. After implement MPLS protocol for multiple VRFs on a single Cisco device, the engineer notices all VRFs on the router still do to not LDP session protection feature enabled.

Which configuration must the engineer apply to enable the LDP session protection feature FOR LDP neighbors within each VRF?

Configure LDP session protection globally on the device only.

Configure LDP session protection globally on the device and on each neighbor that requires session protection.

Configure LDP session authentication on the device to enable LDP session protection on each VRF automatically.

Configure LDP session protection within the individual VRFs.

50. Refer to the exhibit:

Router 1 was experiencing a DDoS attack that was traced to interface gjgabitethernet0/1.

Which statement about this configuration is true?

Router 1 drops all traffic that ingresses interface gigabitethernet0/1 that has a FIB entry that exits a different interface

Router 1 accepts source addresses on interface gigabitethemet0/1 that are private addresses

Router 1 accepts all traffic that ingresses and egresses interface gigabitethernet0/1

Router 1 accepts source addresses that have a match in the FIB that indicates it is reachable through a real interface

Page 6 of 9

51. Which two PHY modes are available to implement an IOS XR Gigabit Ethernet interface interface? (Choose two.)

SONET

MAN

WDWM

LAN

WAN

52. Refer to the exhibit.

An engineer configured BGP summarization on a customer's network.

Which route is advertised to BGP peers?

192.0.0.0/16

192168.0.0/16

192.168.1.0/24

192168.0.5/30

53. Which component is similar to an EVPN instance?

MPLS label

IGP router ID

VRF

router distinguisher

54. What occurs when a high bandwidth multicast stream is sent over an MVPN using Cisco hardware?

Option A

Option B

Option C

Option D

55. DRAG DROP

Drag and drop the OSPF and IS-IS Cisco MPLS TE extensions from the left to their functional descriptions on the right.

56. Which OoS model allows hosts to report their QoS needs to the network?

DiffServ

CB-WFQ

IntServ

MQC

57. What is the function of the FEC field within the OTN signal structure?

It allows the sending devices to apply QoS within the OTN forwarding structure.

It allows source nodes to discard payload errors before transmitting data on the network.

It allows receivers to correct errors upon data arrival.

It allows deep inspection of data payload fields.

58. DRAG DROP

Drag and drop the technologies from the left onto the correct definitions on the right.

59. Refer to the exhibit:

What is the URL used for with REST API?

It is used to contact a URL filter to determine the efficacy of a web address

It is used to send a TACACS+ authentication request to a server

It is used to send a message to the APIC to perform an operation on a managed object or class operator

It is used to initiate an FTP session to save a running configuration of a device.

60. Refer to the exhibit.

A network administrator implemented MPLS LDP changes on PE-A LSR device. The engineer must ensure there are no LDP peer are fully operational.

Which LDP feature must the engineer apply to the existing configuration to eliminate the problem?

Configure MPLS LDP IGP synchronization on the network.

Configure MPLS LDP NSR for all LDP sessions.

Enable LDP session protection under the routing protocol.

Disable IP CEF on routers running LDP and enable LD

Page 7 of 9

61. A remote operation center is deploying a set of l-BGP and E-BGP connections for multiple IOS-XR platforms using the same template. The l-BGP sessions exchange prefixes with no apparent issues, but the E-BGP sessions do not exchange routes.

What causes this issue?

A PASS ALL policy has no! been implemented for the l-BGP neighbors.

The next-hop-self command is not implemented on both E-BGP neighbors.

The E-BGP neighbors are not allowed to exchange information doe to the customer platforms default policy.

The l-BGP neighbors are mistyped and HELLO packets cannot be exchanged successfully between routers.

62. Which statement about the Cisco MPLS TE forwarding adjacency feature is true?

It enables the headend and tailend routers to establish a bidirectional tunnel

It enables the tailend router to advertise routes to the headend router over the tunnel

It enables the MPLS core to use EIGRP as the routing protocol

It enables the Cisco MPLS TE tunnel to be advertised into the running IG

63. Refer to the exhibit.

An ISP provides shared VoIP Extranet services to a customer in VRF-100 with these settings:

✑ The VoIP services are hosted in the 198.19.1000/24 space.

✑ The customer has been assigned the 198.18.10/29 IP address bloc*.

✑ VRF-100 is assigned Import and export route target 85010:100.

Which configuration must the engineer Apply to PE-1 to provision VRF-100 and provide access to the shared services?

Option A

Option B

Option C

Option D

64. Which additional feature does MPLS DiffServ tunneling support?

matching EXP and DSCP values

interaction between MPLS and IGP

using GRE tunnels to hide markings

PHB layer management

65. Refer to the exhibit.

Router P4 and P5 receive the 0.0.0.0/0 route from the ISP via eBGP peering P4 is the primary Internet gateway router, and P5 is its Backup. P5 is already advertising a default route into OSPF domain.

Which configuration must Be applied to P4 so that advertises a default route Into OSPF and Becomes me primary internet gateway for the network?

Option A

Option B

Option C

Option D

66. Refer to the exhibit.

Which show command should be implemented to display per-interface statistics about uRPF drops and suppressed drops?

show ip traffic

showip interface

show cef interface

show ip interface brief

67. A network engineer is deploying VPLS configuration between multiple PE routers so that customer's remote offices have end-to-end LAN connectivity.

Which additional configuration should the engineer perform on the PE routers to enable the virtual switch instance?

A)

Option A

Option B

Option C

Option D

68. What do Ansible and Salt Stack have in common?

They both use DSL configuration language

They both use YAML configuration language

They both have agents running on the client machine

They both can be designed with more than one master server

69. Refer the exhibit.

Users on a network connected to router R3 report slow speeds when they connect to the server connected to R2. After analyzing traffic on the network, a network engineer identified congestion on the link between R2 and R3 as the cause.

Which QoS service must the engineer implement to drop traffic on the link when it exceeds a configured threshold?

first-in, first-out

traffic shaping

class-based weighted fair queueing

traffic policing

70. Refer to the exhibit.

Which type of DDoS attack will be mitigated by this configuration?

SYN flood

smurf attack

SIP INVITE flood attacks

teardrop attack

Page 8 of 9

71. Refer to the exhibit:

Which condition must be met by the OSPF peer of router R1 before the two devices can establish communication?

The interface on the OSPF peer must use the same key ID and key value as the configured interface

The interface on the OSPF peer may have a different key ID, but it must use the same key value as the configured interface

The OSPF peer must be configured as an OSPF stub router

The OSPF peer must use clear-text authentication

72. Refer to the exhibit.

What is the effect of this configuration?

R1 supports a graceful restart operation on the peer, even if graceful restart is disabled on the peer.

R1 supports a peer that is configured for LDP SSO/NSF as the peer recovers from an outage.

R1 failovers only to a peer that is configured for LDP SSO/NS

R1 failovers to any peer.

73. Refer to the exhibit:

Which statement describes this configuration?

Router 1 has its running configuration locked so changes can be made only when the administrator issues a kill session

Router 1 can be remotely managed by the CLI using Telnet

Router 1 has a new data store to collect SNMP information, but configuration must still be done at the CLI only

Router 1 has a temporary data store where a copy of the running configuration can be manipulated and verified before committing the configuration

74. Refer to the exhibit.

EIGRP a running across the core lo exchange Internal routes, and each router maintains 6GP adjacency with the other routers on the network. An operator has configured static routes on the edge routers R1 and R2 for IP address 10.0.1.1. which is used as a black hole route as shown.

Which configuration should the operator Implement to me management rouler to create a route map that will redistribute lagged static routes into BGP and create a static route to blackhole traffic with tag 777 that Is destined to server at 192.168.10.100?

Option A

Option B

Option C

Option D

75. A customer of an ISP requests support to setup a BGP routing policy.

Which BGP attribute should be configured to choose specific BGP speakers as preferred exit points for the customer AS?

highest local preference outbound

lowest local preference inbound

highest local preference inbound

lowest multi-exit discriminator

76. TION NO: 91

Refer to the exhibit:

R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.

Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?

ip ospf network non-broadcast

ip ospf network point-to- multipoint non-broadcast

ip ospf network point-to-point

ip ospf network broadcast

77. The network-engineering team of a service provider is integrating several recently acquired networks into a more scalable common Unified MPLS architecture.

The new network architecture will support end-to-end VPNv4 and VPNv6 services with these requirements:

• The IGP of the core layer is IS-IS In Area 0.

• The IGP of the aggregation layers is OSPF in Area 0.

• The LDP protocol Is used to distribute label bindings within each IGP domain.

Which task must the network engineer perform when implementing this new architecture?

Configure BGP-LU between ABR routers of each IGP domain to carry MPLS label information in NLR

Configure a BGP session between the ABR routers of each IGP domain to exchange VPNv4 or VPNv6 prefixes

Configure the ABR in each IGP domain to preserve next-hop information on all VPNv4 and VPNv6 prefixes advertised by the P

Configure mutual redistribution of each IGP domain's loopback prefix to provide end-to-end LDP LSP

78. Refer to the exhibit.

An engineer configured R6 as the headend LSR of an RSVP-TE LSP to router XR2, with the dynamic path signaled as R6-R2-R5-XR2. and set the OSPF cost of all links to 1. MPLS autotunnel backup Is enabled on all routers to protect the LSP.

Which two NNHOP backup tunnels should the engineer use to complete the implementation? (Choose two.)

The R6 backup tunnel path R6-R1-R4-R5.

The R2 backup tunnel path R2-R5 across the alternate link.

The R2 backup tunnel path R2-R1-R4-XR1-XR2.

The R6 backup tunnel path R6-R2-R5

The R6 backup tunnel path R6-R1-R2.

79. DRAG DROP

Drag and drop the LDP features from the left onto their usages on the right.

80. Refer to the exhibit.

A network operator is attempting to configure an IS-IS adjacency between two routers, but the adjacency cannot be established. To troubleshoot the problem, the operator collects this debugging output.

Which interface are misconfigured on these routers?

Option A

Option B

Option C

Option D

Page 9 of 9

81. Refer to the exhibit.

A network operator must configure CSR1 interlaces GigabitEihernet2 and GigabitEthemet to rewrite VLAN tags 12 and 21 for traffic between R1 and R2 respectively.

Which configurator accomplishes this task?

A)

Option A

Option B

Option C

Option D

82. Refer to the exhibit:

An engineer is preparing to implement data plane security configuration.

Which statement about this configuration is true?

Router 2 must configure a route to null 0 for network 192 168.1 0/24 for the RTBH implementation to be complete.

Router 1 is the trigger router in a RTBH implementation.

Router 1 must be configured with uRPF for the RTBH implementation to be effective.

Router 2 is the router receiving the DDoS attack

83. Which BGP attribute is used first when determining the best path?

origin

AS path

local preference

weight

84. An engineer is implementing IGMP with SSM on a multicampus network that supports video streaming.

Which task must the engineer perform as part of the process?

Configure the network to use IGMPv3.

Configure the network to use bidirectional PI

Configure an RP that uses static assignments only.

Configure the network to use the PIM bsr-candidate

85. A network team has failed to implement IS-IS multitopology.

What is the reason for it?

The router did not support VRFs.

The routing process did not support extended metrics.

The router did not have Cisco Discovery Protocol and Cisco Express Forwarding disabled.

The routing process supported Level 1 only.

350-501 SPCOR Exam Dumps have been Updated

350-501 SPCOR Exam Dumps have been Updated

Share this post

Leave a Reply Cancel reply

Related Posts