NS0-184 Exam Questions have been Updated in August

dumps2022-08-19T02:03:56+08:00

Netapp NS0-184 exam questions have been updated in August, which are helpful for you to pass. In the new updated Netapp certification NS0-184 exam questions, there are 371 Q&As. By studying all of the updated NetApp Certified Storage Installation Engineer, ONTAP NS0-184 questions, you can study the NS0-184 test easily. Free updated Netapp Certification NS0-184 exam questions are below.

Page 1 of 12

1. Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.

Which two actions would enable the customer to accomplish this task? (Choose two.)

Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.

Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.

Deploy a new AFF A400 to the cluster.

Deploy new, dedicated, storage switches for the new NS224 shelves.

2. You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.

In this scenario, which feature should you enable?

cluster switch logging

cluster switch health monitor

IPv6 on all cluster ports

data center bridging protocol

3. Click the Exhibit button.

You are installing a new AFF All SAN Array A700 HA pair.

Referring to the exhibit, which IP address would have been used to join node 02 to the cluster during setup?

192.168.0.112

169.254.212.198

169.254.145.151

192.168.0.101

4. You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.

In this scenario, how would you add the shelf?

Add the shelf to the existing stack.

Create a new stack on the HA pair to add the shelf.

Connect the shelf to an HA pair with NSE drives.

License NSE and add the shelf to this HA pair as a new stack.

5. You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.

Which action must be taken to solve the problem?

Install the license file.

Install the CSHM configuration file.

Install the reference configuration file.

Reboot the controllers.

6. A customer is asked to install a new AFF ASA A700 system. During the installation, the customer asks if ONTAP 9.8 is supported with their host’s OS version running Windows 2016.

In this scenario, which NetApp tool would verify supportability?

ONTAP System Manager

Active IQ Unified Manager

Active IQ OneCollect

Interoperability Matrix Tool

7. Click the Exhibit button.

Which set of components on a FAS9000 are highlighted in the exhibit?

FCVI-Module, Controller, Serial-Port, FlashCache-Module

SAS-Module, Controller, USB-Port, FlashCache-Module

NVRAM-Module, Controller, Serial-Port, FlashCache-Module

Powersupply, Controller, USB-Port, NVRAM-Module

8. You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.

Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

Use ports from different NICs.

Use ports from the same NICs.

Use ports with different chipsets.

Use ports with the same chipsets.

9. You want to enable secure communication with the SP or BMC through CA-signed certificates.

Which two certificate types must be installed in this scenario? (Choose two.)

cluster certificate

server certificate

root CA certificate

ONTAP certificate

10. After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.

What is required to complete this task?

Use the storage port rescan command.

Use the lun mapping add-reporting-nodes command.

Use the lun bind create command.

Rescan the bus on the hosts by using the rescan-scsi-bus.sh script.

Page 2 of 12

11. Which logical interface has a fixed firewall policy?

data LIF

cluster management LIF

cluster LIF

intercluster LIF

12. Click the Exhibit button.

What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

to provide a direct connection for the SnapMirror Synchronous (SM-S)

to install cross-site cluster management switches

to provide connectivity for NVRAM over iWARP

to enable SyncMirror replication

13. You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither “un-failing” nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.

In this scenario, which two actions should you take? (Choose two.)

Ask the customer to open a technical case with NetApp Support.

Ask the customer for a drive with the same capacity and replace it.

Run Active IQ Config Advisor to collect all the logs on the system.

Power off the system until the drive has been replaced.

14. An administrator issued the cluster setup command and configured a 2-node ONTAP 9.8 cluster.

In this scenario, which tool would the administrator use to validate the configuration?

Active IQ Upgrade Advisor

Interoperability Matrix Tool

NetAppDocs

Active IQ Config Advisor

15. You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.

Which two additional steps must be taken to bring the additional ports online? (Choose two.)

Reload the firmware

Reload the RCF file

Re-enable each port

Reload the switch

16. You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.

In this scenario, which two flow control settings would you verify? (Choose two.)

Verify that the data network ports have full flow control disabled.

Verify that the cluster network ports have full flow control enabled.

Verify that the data network ports have full flow control enabled.

Verify that the cluster network ports have full flow control disabled.

17. You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes.

In this scenario, which two resources will help you find a solution? (Choose two.)

Active IQ Config Advisor

NetApp Documentation Center

NetApp Knowledge Base

Active IQ Digital Advisor

18. You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.

In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

Load the Storage RC

Cable the AFF A250 nodes to the next free ports on the switch.

Cable the AFF A250 nodes to the breakout ports on the switch.

Load the Cluster-HA-Breakout RC

19. You are expanding an existing 4-node ONTAP 9.8 cluster with a FAS8300 HA pair by adding a new FAS500f HA pair. Before the expansion, you are asked to save the configuration of the cluster to a backup file.

In this scenario, which two ONTAP configuration backup methods are available? (Choose two.)

storage VM

node

cluster

switch

20. You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.

In this scenario, which two statements are true? (Choose two.)

The AFF A250 requires switches with 40GbE port support.

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 uses the same port for the cluster and the HA interconnect.

Page 3 of 12

21. Click the Exhibit button.

You want to add an AFF A400 system to an existing 4-node cluster.

Referring to the exhibit, which number points to the ports that are used to cable the new nodes to the cluster interconnect switches.

22. Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

23. Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.

In this scenario, what would you tell the customer?

24. Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.

Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

2 paths up, 0 paths down (TCP check)

2 paths up, 0 paths down (UDP check)

larger than PMTU communication succeeds on 4 path(s)

basic connectivity succeeds on 4 path(s)

25. You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster that uses NetApp CN1610 cluster interconnect switches.

In this scenario, what are two valid actions for this installation? (Choose two.)

Add the new nodes to the existing cluster and switches.

Create a new 2-node switched cluster that uses the CN1610 cluster switches.

Create a new 2-node switchless cluster.

Migrate the existing cluster to new switches and add the new nodes.

26. You completed a 2-node AFF A700 installation according to the poster. You run the disk show -fields owner command and notice that all drives are assigned to node 1.

In this scenario, which tool would you use to access documentation and guidelines to solve the issue?

Active IQ Unified Manager

Active IQ One Collect

NET2

NetAppDocs

27. You have a new 2-node FAS8700 ONTAP 9.8 cluster. One of the nodes has 24x16 TB NL-SAS disks assigned and available for a new aggregate. You created the aggregate with one RAID group and two spare disks.

In this scenario, how many data drives are in the aggregate?

28. Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.

The LIFs must use the default intercluster service policy.

The LIFs must be in dedicated broadcast domains an IPspaces.

At least one LIF per node is required on each cluster.

29. After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation.

In this scenario, in which three document formats would you create an inventory report? (Choose three.)

.docx

.html

.pdf

.ps

.xlsx

30. Which command would be used to measure the throughput and latency of traffic between nodes?

qos statistics workload performance show

cluster ping-cluster

network test-path

statistics node show

Page 4 of 12

31. You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by “automatic port placement”.

In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

routes

IPspaces

broadcast domains

subnets

32. Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.

Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

Guide Me

Active IQ

Contracts and Warranties

ASE Corner

33. You are preparing to physically install a new AFF A400 cluster into a customer’s racks. All equipment has been delivered to the customer’s site.

Which three tools do you need to complete this installation? (Choose three.)

additional network cables

Phillips #2 screwdriver

laptop computer

slide rail kit

cable management tray

34. Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.

In this scenario, which two prerequisites should you examine in advance? (Choose two.)

Verify that the hard drives of the new controllers are compatible with the old controllers.

Verify that the existing cluster has a minimum 10 GB of free space for root volumes.

Verify that the existing switches support the additional controllers.

Verify that the platform of the new controllers can be mixed with the cluster’s existing controllers.

35. Click the Exhibit button.

Referring to the numbers shown in the exhibit, which port on an AFF A220 controller is used as port e0M in ONTAP?

36. When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?

RAID 4

RAID-TEC

RAID 0

RAID DP

37. On which type of network interfaces are the cluster interconnect LIFs created?

on an FC or FCoE port

on an interface group

on a UTA port shared with other LIFs

on a physical port

38. You are preparing for the installation of a new ONTAP 9.8 cluster and need to get the preinstallation information from the customer.

In this scenario, which NetApp tool would you use to create a configuration spreadsheet template for the deployment?

Interoperability Matrix Tool

ConfigBuilder

Active IQ Config Advisor

Active IQ Unified Manager

39. You installed two separate clusters in an isolated data center without outbound network access. The customer wants to troubleshoot issues locally and also create custom Excel reports for capacity utilization from a local server.

In this scenario, which NetApp tool would satisfy this requirement?

Active IQ Digital Advisor

Active IQ Unified Manager

Cloud Insights

ONTAP System Manager

40. You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.

In this scenario, what are three examples of data required from the customer? (Choose three.)

management IP addresses

cluster switch name

gateway IP address

BMC IP addresses

cluster name

Page 5 of 12

41. After the successful installation of a NetApp ONTAP cluster, the customer wants to know how to view telemetry data. The customer also wants to receive online information about any risks with the cluster and potential best-practice gaps.

Which tool satisfies the customer’s requirements?

Active IQ Digital Advisor

Interoperability Matrix Tool

Spot by NetApp

Cloud Manager

42. You are setting up a peer relationship between two ONTAP clusters.

In this scenario, which two statements are true regarding authentication?

Peering authentication status can be verified with the cluster peer show command.

Peering authentication can be configured using LDAP users and groups.

Peering authentication is required before enabling peering encryption.

Peering authentication can use an ONTAP generated passphrase.

43. You want to use the NetAppDocs tool to collect information on a newly configured ONTAP 9.8 cluster and to generate a Word document with the details of the cluster configuration.

Which two data sources would you use to collect the necessary data? (Choose two.)

Active IQ Digital Advisor

Active IQ Unified Manager

ONTAP Cluster

AutoSupport packages

44. Click the Exhibit button.

You are attempting to add a new ONTAP 9.7 node to your ONTAP 9.8 NetApp cluster.

After attempting to add the node, it fails as shown in the exhibit.

What are two nondisruptive ways to add the new node to your ONTAP cluster? (Choose two.)

Revert the cluster from ONTAP 9.8 to ONTAP 9.7.

Re-initialize all the nodes in the ONTAP cluster with ONTAP 9.7.

Upgrade the new node from ONTAP 9.7 to ONTAP 9.8.

Add the node using the -allow-mixed-version- parameter.

45. You want to add an AFF A400 HA pair to an existing cluster.

In this scenario, which LIF type is required?

cluster-mgmt

intercluster

data

node-mgmt

46. You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.

In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)

port sets

switch zoning

reporting nodes

failover groups

47. You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.

In this scenario, which front-end FAS8300 network port would you create the data LIFs?

a0a

e0e

e0e-100

a0a-100

48. Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.

In this scenario, which two methods would be supported to migrate the data? (Choose two.)

Perform a controller swap from the FAS8020 to the AFF A250s.

Create a 4-node cluster on one side and use the vol move command to migrate the data.

Use a host-based copy migration method.

Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.

49. A customer wants to enable SnapMirror Synchronous across their environment. The customer must ensure that SnapMirror Synchronous will work across the environment.

In this scenario, which two statements are true? (Choose two.)

A SnapMirror license is required on both the source cluster and the destination cluster.

A SnapMirror Synchronous license is required on both the source and destination clusters.

A SnapMirror license is not required on both the source cluster and the destination cluster.

A SnapMirror Synchronous license is required on the source cluster.

50. Click the Exhibit button.

After installation of a new ONTAP cluster, you experience a problem. You successfully create a support case on the NetApp Support site. The customer asks you how to view the status of the case.

Referring to the exhibit, which two steps would allow the customer to accomplish this task? (Choose two.)

Open https://support.netapp.com, using the partner credentials.

Open https://support.netapp.com, using the customer credentials.

Open My Cases, and select the 41747189 case number.

Open My Cases, and select Create a Case.

Page 6 of 12

51. You are using Broadcom BES-53248 switches for a cluster interconnect in a base configuration.

In this scenario, what is the minimum number of ISLs supported between the switches?

52. Which two switch operating system are supported on ONTAP cluster switches? (Choose two.)

Brocade FOS

Cisco NX-OS

Cisco IOS

Broadcom EFOS

53. You are deploying a new AFF All SAN Array A250 into a customer’s existing data fabric.

In this scenario, which two tools would give insight into their existing Cisco MDS fabric configuration? (Choose two.)

Brocade SAN Health

Cisco Data Center Network Manager (DCNM)

Active IQ

Active IQ Config Advisor

54. A customer is creating a new SVM to host iSCSI LUNs for a Hyper-V cluster. You need to successfully map the new LUNs and make them visible to the Hyper-V cluster.

In this scenario, which host information is required to accomplish this task?

IQNs

WWNNs

WWPNs

host names

55. A customer requires encryption at rest on every node root volume.

In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

NVE

IPsec

NAE

NSE

56. After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.

In this scenario, which two commands would you use to accomplish this task? (Choose two.)

system node autosupport history show

system node autosupport check show

system node autosupport destination show

system node autosupport invoke

57. Click the Exhibit button.

Immediately after installing a 4-node FAS8200 cluster, you discover that node, “cluster1-02”, must be removed from the cluster. You want to use the cluster remove-node command to remove the node.

Referring to the exhibit, which two statements are correct? (Choose two.)

Verify that high availability is configured for failover to the HA partner, then remove the node.

Make the node ineligible by using the cluster modify -eligibility false command, then remove the node.

Move Epsilon to cluster1-02, then remove the node.

Remove the node, then the cluster will elect a new master to remain in quorum.

58. After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues.

In this scenario, which NetApp tool would have identified these errors after the installation process?

Cloud Manager

ONTAP System Manager

Active IQ Config Advisor

Active IQ Unified Manager

59. Your customer wants to know more about the network configuration within the cluster.

In this scenario, which statement is correct about a LIF?

A LIF is a port that provides physical connections.

A LIF is created within a broadcast domain and contains a pool of IP address.

A LIF is an IP address or a WWPN that is associated with a port.

A LIF separates network domains to access cluster data.

60. Data ONTAP 9 supports which three features? (Choose three.)

SMB 3.0

NFSv2

SnapMirror

Infinite Volumes

Page 7 of 12

61. You want to create a data volume on aggr0 and you receive a message with the following warning: ''Warning: You are about to create a volume on a root aggregate.

This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?''

What is the reason for this severe performance or stability problem?

Controller failover and storage failover are separate processes that must occur in parallel, otherwise problems will arise.

The performance load generated by the data volume can be very strong, so it should not be shared with vol0 on aggr0, requiring a separate aggregate for it.

The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiring a dedicated aggregate for it.

Controller failover and storage failover are separate processes that must occur at different times, otherwise problems will arise.

62. You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches. In this scenario.

Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)

network port show -ipspace Cluster

network interface show -vserver Cluster

network device-discovery show -protocol cdp

network interface show -vserver Cluster -fields auto-revert

63. You configured AutoSupport and are trying to send a full AutoSupport message to NetApp. You use the autosupport history show command and see the output shown in the exhibit. The customer confirms that the AutoSupport settings are correct.

Which two actions will solve this issue? (Choose two.)

The customer needs to enable AutoSupport for both nodes.

The customer needs to exclude the two nodes from the attachment-size limitation.

The customer needs to change the transport protocol to HTT

The customer needs to white-list the two nodes on their mail server.

64. Upon finishing the Installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.)

Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples.

If you have a specific issue, you can visit the Knowledge Base Web site (https://kb.netapp,com).

The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com).

You should open a case with NetApp Support for all future questions with low priority and include the keyword "Training" in the title.

65. After you install an AFF A700 2-node cluster with DS224C shelves, Config Advisor reports that your SAS cabling is in mixed-path HA. You expected the SAS cabling be in quad-path HA.

You physically verify the LED status on the controllers and the shelves and notice no irregularities. However, a reboot of the SAS expander does not change the output.

In this scenario, what should you do next?

Open a case with NetApp Support and turn off the disk shelves until the issue is solved.

Disconnect the disk shelves from the controller and run Config Advisor again.

Re-seat the SAS IO modules of the affected AFF A700 controller.

Use multipath HA because it is the only cabling supported on an AFF A700 controller.

66. Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.

In this scenario, which two statements are correct? (Choose two.)

Configure an SNMP community string on the cluster.

Configure DNS on the cluster.

Configure a trap host on the cluster.

Configure a firewall policy and allow SNM

67. You are asked to install six shelves to a production cluster. The cluster is running clustered Data ONTAP and is a 4-node cluster. All six shelves will be cabled to the same HA pair. The customer wants you to assign all the new disks to a single node in the cluster.

Which three tools would help you accomplish this task? (Choose three.)

the Hardware Universe Web-based tool

the Synergy application

the Config Advisor application

the My AutoSupport Web-based tool

the System Setup application

68. You were dispatched to install a cluster made up of FAS8060 and FAS8080 controllers. There are three FAS8060 controllers and three FAS8080 controllers.

Which solution would provide the largest possible cluster?

a cluster made up of two nodes

a cluster made up of four nodes

a cluster made up of five nodes

a cluster made up of six nodes

69. What is the minimum number of disks required in a SAS shelf?

half of the shelf's capacity

one

two

there is no minimum

70. A host cannot connect to the namespace configured on an NVMe-enabled SVM.

In this scenario, what are two reasons for this problem? (Choose two.)

The namespace has not been added to the subsystem

The namespace has not be added to the igroup

The igroup has an incorrect NQ

The subsystem has an incorrect NQN

Page 8 of 12

71. After completing an installation, the customer wants to know how they can manually open a new technical case with NetApp Global Support.

What are three ways to accomplish this task? (Choose three.)

Use the support site.

Use the NetApp Field Portal.

Use the mobile app.

Use a telephone.

Use AutoSupport.

72. You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.

In this scenario, what caused this problem?

Breakout cables were used and the second port on the same ASIC became disabled.

This is a hardware error and you must open a case with NetApp Support.

You must first enable the ports using the network port modify command.

You are missing a license to enable those ports.

73. Which switch vendor is supported for the cluster network switches?

Juniper Networks

Cisco

Brocade

Hewlett-Packard

74. You want to add two new nodes to an existing 4-node cluster.

In this situation, what must be considered regarding the cluster interconnect?

When a new node joins a cluster, IP addresses are generated automatically

When a new node joins a cluster, IP addresses are used from the data LI

When a new node joins a cluster, the customer must give you IP addresses from the customer's local IP range.

When a new node joins a cluster, you must use "class A" subnet settings.

75. An iSCSI LIF fails to migrate during a storage failover test. In this scenario, why did the LIF not migrate?

A failover port was not defined

LIFs that serve block protocols do not failover

The failover policy was not configured

LIF failover was not enabled

76. Click the Exhibit button.

You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does not want ACP cabled on their cluster.

Which two actions would allow the installation to be completed successfully? (Choose two.)

Advise NGS that the customer has a controller in an unsupported state.

Advise the customer that they must acknowledge that they are not using ACP on the installation.

Advise the sales team that the customer is operating without ACP and that the customer is asking you to leave it that way.

Advise the customer that the error will cause the controller to not operate properly and create an unsupported state.

77. A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.

Which port names are correct in this scenario?

e0a/0a, e0b/0b, e0c/0c, e0d/od

e2a/2a, e2b/2b, e2c/2c, e2d/2d

e2a, e2b, e2c, e2d

2a, 2b, 2c, 2d

78. When you start a new Service Event Report, what must be entered first?

the case ID number

the project number

the node serial number

the sales order number

79. What is the main function of ACP?

it allows cabling the shelf to two additional controllers.

It allows the controller to use Ethernet instead of SAS to fetch the storage data.

it allows the controller to nondisruptively reset the SAS expanders.

It enables the automatic shelf ID assignment.

80. You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.

What must you consider before you add the addiHonal nodes to clusterA?

Convert clusterA to a switched cluster by migrating the data lIFs from direct connect to die cluster interconnect switch.

Convert clusterA to a single-node cluster.

Convert clusterA to a switch** cluster by migrating the cluster LIFs from direct connect to the cluster interconnect switch.

Use direct connect to add the additional nodes to cluster

Page 9 of 12

81. Exhibit:

While you are introducing the customer to the NetApp Support website, they ask you to ensure that the new ONTAP storage array is covered by support before you complete the knowledge transfer procedure.

Referring to the exhibit, which two widgets would you select to accomplish this task? (Choose two.)

Active IQ

Product Support

Systems

Contracts and Warranties

82. What are three reasons to implement FabricPool? (Choose three.)

to implement storage efficiency features

to reclaim space on primary storage

to move volumes to external capacity tiers

to use the volume backup feature

to shrink secondary storage

83. You create a new CIFS data LIF with the default failover group. In this scenario, where will the new LIF failover if the node that owns the new LIF panics?

to any port in the cluster that is operationally up

to any port in the cluster that is administratively up

to any available port in the same subnet

to any available port listed in the broadcast domain

84. You are ready to purchase a new FAS8200 six node cluster. In this scenario, which three switches are supported as NetApp cluster interconnect switches.

Cisco nexus 5596UP

Cisco Nexus 5548UP

Cisco Nexus 3132Q-V

Cisco CN1610

Brocode 7840

85. A customer has a 2-node FAS8200 cluster with four DS212C shelves with 10 TB SATA drives.

Referring to the exhibit, an aggregate will be created with which default RAID type?

RAID_DP

RAID_TEC

RAID4

RAID1

86. You are adding new nodes to a 2-node switchless cluster.

According to NetApp, what must you do before adding the nodes?

You must configure cluster peering.

must install interconnect switches.

You must configure vserver peering.

You must enable a cluster HA

87. You have set up a new 2-node switchless cluster and want to verify that the failover is configured correctly.

In this scenario, which two commands accomplish this task? (Choose two.)

cluster ha show

storage failover show

cluster ring show

storage failover show-takeover

88. While troubleshooting an issue with a newly installed system, you used the system controller environment show command.

In this scenario, which issue would be diagnosed with this command?

controller configuration issues

controller hardware issues

shelf cabling issues

controller version issues

89. According to NetApp documentation, what should be used when using the Cluster Switch Health Monitor (CSHM) and log collection features?

Telnet

HTTP

SSL

SSH

90. A customer wants to graphically manage a new clustered Data ONTAP system.

Which tool should the customer use?

System Setup

OnCommand System Manager

HostAgent

StorageGrid

Page 10 of 12

91. A customer is installing a new system. The administrator needs to have the maximum available amount of data space.

Which disk configuration should the administrator use?

RAID-DP

RAID4

Flash Pool

ADP

92. Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it.

In this scenario, how would you access Node 4’s management interface?

You must use the Service Processor; node management LIFS do not fall over between nodes.

You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.

You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.

Connect to the node management on Node 3 and then use the HA interconnect to access node 4.

93. You are setting up a LIF for the node management network.

What will be the default failover policy in this scenario?

broadcast-domain-wide

system-defined

local-only

sfo-partner-only

94. What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster? (Choose two.)

Flash Pool

FlexClone volumes

FlashCache

thin provisioning

95. What is the purpose of a mailbox disk?

for shipping defective drives back to NetApp

for storing HA partner information

for logging

for sending AutoSupport mail

96. You are assigned to install two DS2246 shelves, three DS4243 shelves, and one DS4486 shelf.

How many rack units (U space) should you account for in this rack layout?

20U

10U

22U

97. Which license is required to enable storage failover?

CFO

no license is required

SFO

98. Poppy Pet Care Kennels offers short-term accommodation for dogs whilst their owners are on holiday. The managing director of the company has initiated a project to create a new website that will allow owners to view kennel availability, book kennel accommodation and allow them to monitor their dogs whilst they are away, via a webcam.

The system will also allow kennel assistants to plan the dogs’ feeding times and schedule kennel maintenance.

Customers will be able to leave feedback on the website, which will be reviewed by the quality manager who may respond to comments made by the customer.

The following are potential actors:

A) Poppy Pet Care Kennels

B) Kennel assistants

C) The managing director

D) Customers

E) Quality manager

Which of these would be drawn as actors on the use case diagram?

A, B and C

A, D and E

B, C and E

B, D and E

99. What is a valid failover policy for a SAN LIF?

disabled

broadcast-domain-wide

system-define

local-only

100. Exhibit:

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.

Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

Relocate the switches or the AFF A400 so that the distance is less than five meters.

Install 10 meter NetApp supported copper cables.

Change the requirement for Ethernet cables.

Change the requirement for optical cables.

Page 11 of 12

101. You are planning to update your running switch environment. You need to determine if certain conditions exist before the FASTPATH software and reference configuration file (RCF) on a NetApp CN16xx cluster switch can be installed.

Which condition must exist in this scenario?

You must set the port configuration to default for all ports before running the portcfgdefault portnumber command.

The cluster must be a fully functioning cluster (no error log messages or other issues).

All ISL ports must be moved to a different switch.

You can only update your switch environment within offline windows.

102. You finished the Installation of a 2-node cluster and want to determine correctly.

What are two ways to accomplish this task? (Choose two.)

Use the OnCommand Performance Manager GU

Use the cluster ha show and storage failover show commands on the C

Use the system node autosupport check show command on the C

Use the OnCommand System Manager GU

103. What is the next step if you must escalate an open case?

Upload the support case and core data files to NetApp Suport and to Engineering.

Clustered Data ONTAP triggers the AutoSupport mechanism automatically again.

Call NetApp Support and ask to speak to the duty manager.

Call NetApp Support and open a new case.

104. You are performing HA failover tests on a 2-node cluster with FAS8200 controllers. You want to observe the boot process for the storage node in takeover.

To which interface should you connect to accomplish this task?

Service Processor

SVM management

cluster management

node management

105. A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves.

What would you advise the customer in this scenario?

Convert the ACP communication from out-of-band to In-band channel.

Remove the ACP cabling from the stack before adding the new shelves.

Remove the DS4243 shelves, but you must add the new DS4246 shelves to a new stack.

Configure the shelf IDs of the new DS4246 shelves to match the existing DS4246 shelves.

106. You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.

Which tool would you use to accomplish this task?

Active IQ scheduled reports

NetAppDocs output report

ONTAP System Manager

Active IQ Config Advisor worksheet

107. You are deploying a cluster with four AFF A300 nodes and Cisco 3232C switches. When you arrive at the customer’s site, you notice that there are multiple breakout cables and four Cisco 3232C switches.

In this scenario, which statement is true?

A 4-node AFF A300 cluster requires four Cisco 3232C switches.

Cisco best practices require four Cisco 3232C switches for high availability.

A 4-node AFF A300 cluster requires two Cisco 3232C switches for the cluster interconnect and two for management.

Your customer ordered a MetroCluster IP configuration.

108. You have a 4-node FAS8060 cluster. You are using the vol move command to relocate a volume from an aggregate on node 1 to an aggregate on node 4.

In this scenario, which network is used for the traffic being relocated?

the node management network

the HA interconnect

the Intercluster network

the cluster interconnect

109. A customer has a six-node cluster running NFS and FCP. The customer wants to add nodes to the cluster.

How many nodes would be added in this scenario?

110. Where is user data (file access) written to by default?

Aggr0_root

Vol0_root

mailbox disks

SVM volume

Page 12 of 12

111. You are preparing to install a new clustered Data ONTAP system.

Which tool prepares all the relevant customer and configuration information?

AutoSupport

Cluster Config Builder

OnCommand System Manager

Config Advisor

112. After the Installation of a new 2-node cluster, you want to make sure that AutoSupport is working as expected from the cluster.

In this scenario, what are two ways to trigger a new AutoSupport? (Choose two.)

Use the ping command on the mailhost.

Use the OnCommand Unified Manager GU

Use the OnCommand System Manager GU

Use the system node autosupport invoke -type test command.

113. You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected.

In this scenario, what would cause this behavior?

The network port is configured incorrectly.

The broadcast domain is configured incorrectly.

There are no online ports within the same failover group.

The network failover port is not licensed.

114. To ensure that your customer’s cluster is robust and operational, you need to be familiar with configuration best practices.

Which three practice rules should you always follow? (Choose three.)

Keep all nodes in the cluster on the same version of ONTA

Use LIFs with defined failover policies.

Remove failed disk drives once a year to maintain minimum interruption in your controller stability.

All power supply units should be plugged into the same power grid.

Do not use the root aggregate for storing data.

115. Which tool checks a newly installed environment for configuration errors?

FilerView

BNA

Synergy

Config Advisor

NS0-184 Exam Questions have been Updated in August

NS0-184 Exam Questions have been Updated in August

Share this post

Leave a Reply Cancel reply

Related Posts