NetApp Certified Support Engineer-ONTAP Specialist NS0-592 Exam Dumps

dumps2022-01-24T03:27:05+08:00

Netapp Certified Support Engineer-ONTAP Specialist NS0-592 exam is easy to take with the latest Netapp Certification NS0-592 dumps questions. To take Netapp NS0-592 exam, you need to have 6-12 months of experience with troubleshooting, analysis, and resolution of Netapp ONTAP Storage System. We provide the online Netapp NS0-592 exam dumps for you to prepare.

In real NCSA-ONTAP Specialist NS0-592 exam, there are 60 questions, and you have 2 hours to take the test. All the latest Netapp NS0-592 exam dumps can help you all the related topics. Free Netapp Certification NS0-592 exam dumps are available below.

Page 1 of 2

1. A customer has created an interface group (igroup) named a0a, a VLAN named a0a-2500, and a data LIF associated with the VLAN interface that has been assigned an IP of 10.254.10.100. The customer is able to ping 10.254.10.100 from a Windows client without any issues, but data traffic is not working.

In this scenario, what is the solution to the problem?

Disable flow control on the a0a interface.

Configure an appropriate service policy for the data LI

Correct the MTU mismatch between the broadcast domain configuration and the upstream network switches.

Allow data traffic by using LIF firewall policies.

2. You migrated from a FAS3250 system to a new A200 system. After the migration, you notice that data compaction fails to be enabled on the migrated volumes.

In this scenario, which statement is correct?

You need to schedule background deduplication on all volumes.

You need a license to have full efficiency on AFF systems.

Data compaction is not supported on the A200 system.

The volumes are thick-provisioned.

3. Click the exhibit button.

A customer has an FC SAN with brocade switches. Each server attached to the SAN gas four FC ports. The customer describes that one of their servers has only four paths to the LUNs configured on the cluster. There should be eight paths on all the other servers. The switch administrator has verified the zone configuration.

Referring to the exhibit, which two actions would you perform to troubleshoot the problem? (Choose two.)

Review the LIF configuration on the cluster.

Review the driver version on the server.

Review that the host side FC link ports are enabled.

Review the igroup configuration on the cluster.

4. Click the exhibit button.

When you log in to a node, a warning is displayed as shown in the exhibit.

Which statement is correct in this scenario?

The node root volume was moved to a new aggregate.

The partner still hosts the CFO aggregate for the node.

One or more RDB db files are damaged due to an internal software error.

The node cannot communicate with the rest of the nodes in the cluster.

5. You are running a fabric-attached MetroCluster configuration with ONTAP 9.5software. There is a maintenance window for the upcoming weekend. Plexes in your mirrored aggregates between your two data centers have not been synchronizing for two days.

When the resynchronizations begin, they are not as quick as expected, and the process takes more than a day.

You have been modifying the number of concurrent I/O streams using the storage raid-options modify raid. resync.num_concurrent_ios_per_rg command, but the resynchronization speed stays slow.

You have four separate ISLs between your data centers using Brocade 6510 switches.

Hardware problems are not an issue.

Which two actions should you take to prevent this problem in the future? (Choose two.)

Update to at least ONTAP 9.4 software.

Restart the resynchronizations after modifying storage raid-options modify raid.resync.num_concurrent_ios_per_rg command.

Avoid changes on your aggregates during the maintenance window.

Take the corresponding plexes offline before maintenance to avoid a base-level synchronization.

6. Click the exhibit button.

Your customer is calling about their MetroCluster environment. They have provided you with the output of the metrocluster interconnect adapter show command.

Referring to the exhibit, which statement is correct?

For all MetroCluster configurations, this is expected output.

The InfiniBand cables should be connected in this configuration.

The InfiniBand interconnect is not used in MetroCluster.

This is a 2-node MetroCluster.

7. Click the exhibit button.

The storage administrator for the company example.com is attempting to join an SVM to their Active Directory as SVM1. The computer account must also be joined to the Secure organizational unit. Attempts to perform this action using the CLI fail with the error message shown in the exhibit.

What is the reason for this error?

The requested OU Secure does not exist in the Active Directory and must be created by the Active Directory administrator.

The requested OU Secure has incorrect principal and errored with KRB5KDC_ERR_S_PRINCIPAL_UNKNOW

The administrator account password used in vserver cifs create was not entered correctly.

The syntax is incorrect; it should be vserver cifs create -cifs-server svm1 -domain example.com -ou ou=Secure, dc=example, dc=com.

8. A reboot was performed by a watchdog reset on the node.

In this scenario, which statement is true?

The service processor no longer responds.

In case of an L1 watchdog event, determine whether a panic message was recorded.

In case of an L2 watchdog event, determine whether a core was dumped.

The wafl_check command should be executed.

9. In a 4-node MetroCluster cluster, both clusters are alerting that the connection to an ATTO bridge is lost.

Which three components should be verified to determine what is causing this problem? (Choose three.)

the SFPs that are connecting the ATTO bridge to the switch

the dark fiber cables between sites

the ATTO bridge

the SFPs in the storage controllers

the fiber cable that is connecting the ATTO bridge to the switch

10. Your customer has initiated several volume move commands to redistribute the workload in their 8-node cluster. To verify that this process is not affecting their client access, they were monitoring the network switches that provide client access, but they do not see the network load of the volume move command.

In this scenario, what is the reason for the behavior?

The volume move command uses the HA iWarp interconnect, not the client access switches.

The volume move command uses copy offload protocol, so it does not show up when monitored.

The volume move command uses the intercluster LIFs, not the data LIFs.

The volume move command uses the cluster interconnect switches, not the client access switches.

Page 2 of 2

11. Click the exhibit button.

Your customer reports that their FAS2554A system reports multi-path HA when running the sysconfig command. However, Config Advisor reports an error about incorrect cabling.

What are the two reasons for the messages? (Choose two.)

Shelves 10 and 20 have different IOM modules and must be in separate stacks.

The FAS2554 system is cabled incorrectly to shelf ID 20.

The DS2246 shelf is wrong; the shelf ID must be 11.

Disk shelves 10 and 20 are cabled incorrectly to each other.

12. Click the exhibit button.

A customer reports that when they are failing over Hyper-V VMs, the process fails, and the server reports an error that indicates that there is something wrong with the storage.

Referring to the exhibit, which three actions would be required in ONTAP to solve this problem? (Choose three.)

Verify that the -symlink-properties parameter is enabled on the share.

Verify that the access-based-enumeration share parameter is configured.

Verify that the continuously -available share parameter is configured.

Verify that -offline-files parameter is set to manual on the share.

Verify that the oplocks share property is configured.

13. Click the exhibit button.

Many end users are complaining that logging in their systems takes a long time. When the login to the desktop finishes, everything is fine. The home directories are on NetApp storage. You do not see any significant disk or CPU contention on the controller, so you gather output statistics from the controller and focus on SMB.

Referring to the exhibit, which two actions would help diagnose the problem? (Choose two.)

Engage your Windows team to make sure that the domain controllers are not overloaded.

Engage your desktop team to collect network traces from the clients.

Collect more statistics to determine whether the controller itself is causing latency.

Engage your network team to make sure that there are no issues between the storage controller and the domain controller.

14. Click the exhibit button.

A customer is reporting that numbers in the statistics volume show command output appear to be incorrect.

Referring to the exhibit, which statement is correct?

The problem is due to a difference in operation size.

Perfstat should be used to explain the behavior.

There are operation types that are not listed in the output.

A case with NetApp should be raised to find the root cause.

15. Click the exhibit button.

You have just cabled a new shelf to a FAS8200. Running the system node run -node * sysconfig - a command indicates that multipath HA is configured. However, after running Config Advisor, you receive an error that your cabling is incorrect.

As indicated in the exhibit, which two actions will correct the cabling? (Choose two.)

Move the 0b SAS connection on the bottom controller to 0d on the bottom controller.

Move the 0b SAS connection on the top controller to 0d on the top controller.

Move the 0b SAS connection on the top controller to 0d on the bottom controller.

Move the 0b SAS connection on the bottom controller to 0d on the top controller.

16. Click the exhibit button.

You are troubleshooting a system in which the customer reports that aggregates on Stack 6c/12b are having slow response tomes from system NETAPP1CLUS-02.

Referring to the exhibit, which two statements are correct? (Choose two.)

The aggregates have only one PHY running at six gigabits per second on 6c.

PHY 2 is running at six gigabits per second; on system NETAPP1CLUS-02, reseat IOM6 Module A on Shelf 10.

The shelf module firmware is downrev; on system NETAPP1CLUS-02, replace IOM6 Module A on Shelf 10.

The aggregates have only PHY at six gigabits per second on 12b.

17. Click the exhibit button.

Referring to the exhibit, which change is required to enable the CIFS Autolocation function for the Users share?

Edit the CIFS share’s properties to remove the changenotify property.

Re-create the LIFs to allow both CIFS and NFS protocols.

Change the CIFS share’s Symlink Properties parameter to symlinks.

Modify the CIFS server’s option to enable SMB multichannel.

18. A customer reports that a LUN is offline because the volume is out of space even though the space-reserve parameter is configured to enabled on the LUN.

Which two statements are correct in this scenario? (Choose two.)

The containing aggregate is thin-provisioned.

The fractional reserve is set to 0%.

Deduplication is inflating the LUN when it is brought online.

The volume has snapshots.

19. Click the exhibit button.

A storage administrator reports that when they enabled Vscan, they began receiving reports of CIFS users having very slow access to all their files. The storage administrator recovered from the issue by disabling Vscan on their SVM. The storage administrator was able to collect perfstat output during the time of the reported slow access, as shown in the exhibit.

In this situation, what is the problem?

The problem is on the SVM, as shown in the scan_latency output.

Vscan server 192.168.100.144 was slower than Vscan server 10.23.23.54 in completing Vscan requests.

Vscan server 10.23.23.54 was slower than Vscan server 192.168.100.144 in completing Vscan requests.

The problem was with both Vscan servers 192.168.100.144 and 10.23.23.54.

20. A customer reports that a takeover has been disabled on an HA pair.

What would be a cause for this to happen?

The HA interconnect is not functioning properly.

There is a disk running too hot.

The interface for the hardware assist has become unavailable.

The cluster network is not functioning properly.

NetApp Certified Support Engineer-ONTAP Specialist NS0-592 Exam Dumps

NetApp Certified Support Engineer-ONTAP Specialist NS0-592 Exam Dumps

Share this post

Leave a Reply Cancel reply

Related Posts