Valid Netapp NS0-176 Exam Questions and Answers

dumps2021-09-29T07:30:54+08:00

Netapp NS0-176 exam is for FlexPod Implementation and Administration Specialist certification. There are 60 questions in real Netapp certification NS0-176 exam, and you have 90 minutes to complete all the questions. All of Netapp NS0-176 exam questions and answers can guarantee you pass. Free Netapp certification NS0-176 exam dumps questions are avaialble below.

Page 1 of 3

1. Which three are types of Storage Virtual Machines? (Choose three.)

data

cluster

flex

intercluster

node

vFiler

2. A customer with several large Cisco MDS 9718 switches wants to reduce the number of total zones and the number of commands required to add devices, while still adhering to best practices.

In this scenario, which two configurations should be implemented? (Choose two.)

Use the zone convert command to migrate existing zones.

Enable SMART Zoning for new VSANs.

Use the zone copy command to migrate existing zones.

Disable SMART Zoning for new VSANs.

3. What is the maximum number of nodes that a NetApp SAN cluster supports?

4. Exhibit:

Referring to the exhibit, what do the asterisks on the left indicate about the output of the ~show zoneset active~ command?

A redundant path is present.

The device is not currently logged in.

Only a single path is present.

The device is currently logged in.

5. An administrator is trying to present an NFS datastore to an ESXi host.

Which two must be available before mounting? (Choose two.)

export policy access

host name case sensitivity

junction path case sensitivity

datastore name case sensitivity

6. You are installing two NetApp FAS8080 EX controllers.

Which two ports would you use for HA connectivity? (Choose two.)

ib0b

ib0a

eof

e0e

7. Refer to the exhibit.

Which is correct for configuring FCoE?

vlan 33fcoe vsan 43int po11switchport trunk allowed vlan add 33int vfc11bind interface po11switchport trunk allowed vsan 43vsan databasevsan 43 interface vfc11

vlan 33fcoe vsan 43int po21switchport trunk allowed vsan add 43int vfc11bind interface po21vsan databasevsan 43 interface vfc 11

fcoe vsan 43int po11switchport trunk allowed vsan add 43vsan databasevsan 43

fcoe vlan 33int po11switchport trunk allowed vlan add 33vsan databasevsan 33

fcoe vsan 43int po21switchport trunk allowed vsan add 43vsan databasevsan 43

8. You are asked to increase read performance for a single aggregate; however, there are no PCI-e slots available in the NetApp cluster nodes.

In this scenario, which feature meets these requirements?

Thin Provisioning

Flash Cache

Advanced Drive Partitioning

Flash pool

9. What determines the size of the .vswap file for a VMware VM?

the size of the RAM plus the log file

the amount of RAM assigned to the VM minus the amount of RAM reserved

the RAM assigned to the VM

the total amount of RAM used by the ESXi host

10. When creating local user, which two are valid user names? (Choose two)

daemon

somebody

root

1greatuser

12345

best_user

11. You are installing a FlexPod Express solution with a NetApp AFF A250 at a customer's remote site.

In this scenario, which two devices are required to provide an NFS v3 datastore? (Choose two.)

Cisco UCS 6324 Fabric Interconnects

Cisco Nexus 3000 Switches

NetApp BES-53248 Switches

Cisco UCS 6454 Fabric Interconnects

12. When installing an instance of VMware ESXi on a UCS B-Series server, where should an ISO image be loaded?

From the UCS Manager select KVM Console, Select the Virtual Media tab, and select Add Image

ISO images should not be used

Only physical install disks are supported on UCS B-Series servers

The UCS vCenter Plugin must be used

13. You are deploying a new virtual machine (VM). Your customer requires that the VM cannot reserve space on the VMFS filesystem, and the VM can only consume blocks when data is written to disk from and within the VM/Guest OS.

Which virtual disk should you create to meet these requirements?

Thick Provision Lazy Zeroed

Thin Provision

Thick Provision Eager Zeroed

Independent Nonpersistent

14. What are two valid cluster interconnect switches? (Choose two.)

NetApp CN610

Cisco Nexus 5596

Cisco Nexus 9504

Cisco Nexus 7004

15. A customer asks you to configure QoS on a Cisco Nexus 7000 Series switch within a FlexPod solution.

Which three steps are required to accomplish this task? (Choose three.)

Attach policies to logical or physical interfaces and VLANs.

Define traffic classes.

Associate policies and actions with each traffic class.

Attach policies to logical or physical interfaces and VSANs.

Perform a shut/no shut on the affected interfaces.

16. A Cisco UCS chasis has two power suppliers connected to one PDU and two power supplies connected to another PDU. You would like to protect against the failure of one entire PDU.

In this scenario, which power policy should you configure in UCS Manager?

N+1

redundant

N+2

grid

17. Which two statements about HA pairs in a NetApp cluster are true? (Choose two.)

In the event of a storage failover, the surviving node provides read/write access to the partner’s disks until the failed node becomes available again.

Non-disruptive aggregate relocation can be performed between HA pairs without a takeover and giveback.

HA pairs in the same chassis are not connected to each other through an HA interconnect.

In the event of a storage failover, the surviving node always takes over the partner's data LIFs.

18. An administrator has a FlexPod solution for use with a VMware vSphere 6.0 environment. The virtual environment consists of virtual machines running both Windows Server 2012 R2 and Windows Server 2008.

The administrator determines that the Windows Server 2008 virtual machine VMDKs are misaligned. The problem needs to be solved without incurring downtime on the virtual machines.

Which tool enables the administrator to solve the problem without virtual machine downtime?

VMware vRealize Operations

NetApp mbralign toolkit

NetApp Virtual Storage Console

UCS Central

19. Which three are characteristics of a NAS data LIF? (Choose three.)

It can be associated with a Fibre Channel port.

It can be associated with a WWPN

It can be associated with an Ethernet port or VLAN interface.

It can be associated with an interface group (ifgrp).

It can be associated with an IP address.

It is associated with the administrative Vserver.

It is associated with the management LI

20. How many VEMs can one server have?

unlimited

Page 2 of 3

21. An administrator has a FlexPod solution and is using OnCommand Unified Manager and OnCommand Performance Manager to monitor the FlexPod environment. Full integration has previously been configured between the two OnCommand virtual appliances; however, new performance issues are not being seen in the OnCommand Unified Manager dashboard.

In this scenario, which two settings should the administrator verify? (Choose two.)

Ensure that the Event Publisher user credentials are entered correctly on the OnCommand Performance Manager appliance.

Ensure that the NetApp cluster is configured to forward SNMP data to OnCommand Performance Manager.

Ensure that OnCommand Performance Manager is licensed for use with OnCommand Unified Manager.

Ensure that network connectivity exists between the two virtual appliances.

22. Exhibit:

Which Cisco switch is shown in the exhibit?

Nexus 2232

Nexus 5548

Nexus 5596

Nexus 7004

23. Which two LIFs are able to failover or migrate to other nodes in the cluster? (Choose two.)

cluster LIF

data LIF of protocol CIFS

data LIF of protocol FCoE

data LIF of protocol iSCSI

data LIF of protocol NFS

intercluster LIF

node management LIF

24. You want to run the FlexPod execution profile in NetApp Config Advisor.

Which three login credentials are required to perform this task? (Choose three.)

NetApp cluster

NetApp support login

UCS Manager

ESXi server

Nexus switches

25. When creating a virtual machine in VMware vSphere 5.x, which type of virtual disk should be provisioned if you would like to fully pre-allocate storage with the highest chance of being contiguous?

Thick Provision Lazy Zeroed

Thin Provision

Full Provision

Thick Provision Eager Zeroed

26. How are jumbo frames enabled on the Nexus 5548?

policy-map type network-qos JUMBOclass type network-qos class-defaultmtu 9216system qosservice-policy type network-qos JUMBO

system mtu jumbo 9000

system qosmtu 9216

policy-map type queueingclass type queueing class-defaultmtu 9216

system jumbo-frame

27. Your UCS environment has recently been upgraded to include UCS B-Series Servers, UCS C-Series Servers, a UCS mini, and a fourth UCS domain. With these new changes, you need a management tool to help you manage the entire environment from a single location.

In this scenario, which tool would you use?

UCS Director

UCS Manager

UCS Central

Cisco Smart Advisor

28. NetApp recommends that your SSL key length be?

512

768

1024

9216

29. You are asked to create an interface group on a NetApp clustered Data ONTAP system. The system is connected to a Cisco Nexus switch in a vPC configuration with the port-channel mode set to active.

Which NetApp interface group made matches this switch configuration?

multimode

multimode_lacp

singlemode

mode active

30. You have a NetApp clustered Data ONTAP storage system and vSphere 6 cluster. You discover that VMware VAAI for NFS is not showing as enabled on one of the five ESXi hosts in your vSphere cluster.

In this scenario, what must you do to enable VAAI for NFS on that ESXi host?

Set the DataMover. HardwareAcceleratedInit advanced setting to 0 on the ESXi host.

Enable VMware vStorage for NFS on the NetApp SV

Enable NFSv3 on the storage system.

Install the NetApp NFS Plug-in for VMware VAAI on the ESXi host.

31. Which LIF role is used for SnapMirror traffic on a system running clustered Data ONTAP?

intercluster

node-management

interconnect

cluster-management

32. Exhibit:

Your vSphere host is booting off an SD and is displaying the error shown in the exhibit.

What should you do to correct the problem?

Enable Unified Extensible Firmware Interface (UEFI).

Enable SD card mirroring.

Update the current ESXi scratch location.

Reinstall ESXi on a larger SD card.

33. In which two locations is the VSAN ID configured in a FlexPod solution? (Choose two.)

Storage Virtual Machine

UCS Manager

Nexus switches

hypervisor adapter

34. How do the Fabric Interconnect ports connecting to the 2232PP FEX have to be configured?

In UCS Manager, the FI ports connecting to the FEX must be set as type ‘Server’

In UCS Manager, the FI ports connecting to the FEX must be set as type ‘FEX’

In UCS Manager, the FI ports connecting to the FEX must be set as type ‘Uplink’

In UCS Manager, the FI ports connecting to the FEX must be set as type ‘Auto’

In UCS Manager, the FI ports connecting to the FEX must be set as type ‘Network’

35. Which two are correct about VSAN configuration within UCS Manager? (Choose two)

VSAN ID and FCoE VLAN ID have to match.

VSAN can be configured as fabric interconnect specific.

We can delete VSAN 1.

VSAN IDs 3840-4079 are not available regardless of the Fabric Interconnect mode.

VSAN can be configured as a global parameter.

In addition to SAN tab, VSANs can be configured under UCSM Server tab as well.

36. Exhibit:

An iSCSI SAN boot is not working for a new Cisoc UCS service profile. The new vNIC template was created using the settings shown in the exhibit.

What should you do to make iSCSI SAN boot work?

Specify a QoS policy.

Change the MAC pool to “<not set>”.

Set the iSCSI-A-VLAN as the “Native VLAN”.

Change the vNIC template to type “Initial Template”.

37. To install your VEM, what is the extension of the VEM file name you’ll be looking for to complete this install?

.zip

.vem

.vib

.vsm

38. Which set of commands maps VLAN 100 to VSAN 100?

Nexus 5000-A#configure terminal Nexus 5000-A (config) # vlan 100 Nexus 5000- A (config-vlan_ #fcoe vsan 100

Nexus 5000-B# configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-B (config-vsan)# vsan 100 Nexus 5000-B(config- vsan) #vsan 100 name FCoE-VLAN 100

Nexus 5000-A#configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-A (config)# vsan 100 Nexus 5000-A (config-vsan) # fcoe vsan 100

Nexus 5000-B# configure terminal Nexus 5000-B(config-vsan) # vlan 100 Nexus 5000-B (config-vsan)# vsan 100 name vsan100

39. For a ‘boot from SAN’ configuration, which two features must be enabled? (Choose two)

FCOE

UDLD

NPIV

FCSP

VPC

40. A disaster occurred and both Cisco UCS Fabric Interconnects must be replaced. You must restore the system from a "full state" backup.

Which two steps will accomplish this task? (Choose two.)

Remove the current firmware from the new Fabric Interconnects.

Restore the "full state" backup through the primary Fabric Interconnect's initial system setup wizard.

Restore the "full state" backup using the UCS Manager "import configuration" wizard.

Upgrade the new Fabric Interconnects to the same version of firmware as the previous Fabric Interconnects.

Page 3 of 3

41. Which is a valid connectivity option for a FlexPod?

Note some of these may also be 'valid' options outside of a FlexPod architecture but do not specifically meet FlexPod scalability and availability requirements.

UCS B-Series > 2232PP FEX > UCS FI > Nexus 5548 < FAS

UCS C-Series > 2232PP FEX > UCS FI > Nexus 5548 < FAS

UCS B-Series direct attach FAS

UCS C-Series > Nexus 3048 < FAS

UCS C-Series direct attach FAS

UCS B-series > UCS FI > 2232PP FEX > Nexus 5548 < FAS

UCS B-Series > UCS FI > Catalyst 3750 < FAS

42. Which sends support summary information to NetApp through HTTPS?

AutoSupport

FlexSupport

SnapSupport

TechSupport

43. Exhibit:

You have a NetApp cluster and have just performed a storage failover giveback command from the CLI.

Referring to the exhibit, what is the status of the storage failover process?

The giveback failed because cluster-01 was not able to communicate with the partner’s cluster LIFs.

The giveback is partially completed waiting for node cluster-01 to give back the partner’s SFO aggregate.

The giveback is partially completed waiting for node cluster-02 to give back the partner’s SFO aggregate.

The giveback failed because the partner node was not in a “waiting for “giveback” state.

44. What management solution can provision all three components of a FlexPod (NetApp storage, Cisco UCS compute and Cisco Nexus network)?

Cisco UCS Central

Cisco FlexPod Manager

NetApp OnCommand Insight

Cisco UCS Director

NetApp FlexPod Manager

45. Which management tool is used to configure and monitor centralized policies for multiple Cisco UCS domains?

UCS Manager

UCS Director

UCS Central

UCS Performance Manager

46. Which two features allow multiple fabric logins through a single port? (Choose two.)

NPIV

vPC

NPV

LLDP

47. An administrator is configuring a Flexpod Datacenter solution. The UCS service profiles will use FCoE connectivity to the NetApp cluster.

Which pool is needed to configure the vHBA templates?

WWPN pool

MAC pool

IQN pool

WWNN pool

48. When connecting the Nexus 1110-X to the Nexus switch, what Spanning Tree port type is used?

Edge

Trunk

Network

Edge trunk

Normal

49. Which two are required for single-wire management for Cisco UCS C-Series? (Choose two)

UCS Manager 2.1 or higher

VIC 1240

Redundant Nexus 2232PP FEX

10 GB LOM

FI 6200 family only

VIC 1225

50. When using Clustered Data ONTAP 8.1 and later, what is the default for new aggregates?

32-bit aggregates

64-bit aggregates

128-bit aggregates

cluster aggregates

traditional aggregates

Vserver aggregates

51. Which two are two possible features of the ‘Call Home’ feature in UCS Manager?

Generates a text message to configured cell phone numbers

Generates a syslog event

Ability to proactively open a case with the Cisco TAC with the ‘Smart Call Home’ feature

Generates emails to predefined email addresses when a problem is detected

Allows UCS to proactively pull down new software updates from Cisco

52. You installed a new NetApp cluster running clustered Data ONTAP. There is a single Storage Virtual Machine (SVM) named esx1 on the cluster.

A volume named esx_datastore1 is created in the SVM esx1. The name of the root volume for the esx1 SVM is esx1_rootvol. The default export policy was applied to the volume esx1_rootvol.

You verified that the export policy applied to esx_datastore1 contains a single rule that allows all clients to mount the volume as read/write using any version of NFS. A Linux client attempts to NFS mount the volume and receives a Permission Denied error.

In this scenario, what caused this error?

NFS has not been configured on the SVM esx1.

The volume esx_datastore1 has not been mounted into the namespace of the esx1 SV

UNIX permissions for the volume esx1_rootvol are not set to read/write.

The default export-policy does not have at least one rule to allow all clients read-only access.

53. You are attempting to establish a cluster peer relationship between two NetApp clusters, but the peering process fails.

What is a cause for this failure?

The intercluster LIF on each node cannot communicate with the intercluster LIF on each node in the peer cluster.

The cluster LIFs on each node cannot communicate with the cluster LIFs on each node in the peer cluster.

The node management LIF on each node cannot communicate with the node management LIF on each node in the peer cluster.

The cluster management LIF for the cluster cannot communicate with the cluster management LIF for the peer cluster.

54. Given the following switch output, where would you expect see notification level messages?

N5K-1# show logging info.

Logging console: enabled (Severity: error)

Logging monitor: enabled (Severity: informational)

Logging linecard: enabled (Severity: emergency)

Logging fex: enabled (Severity: notifications)

Logging time stamp: seconds

Logging server: disabled

Logging logfile: enabled

On the console

On the terminal sessions

On the linecard

Notification messages will not be seen anywhere

55. Which type of pools do you need to create vHBA templates?

MAC

WWNN

IQN

WWPN

56. Click the Exhibit button.

On your NetApp storage system, you create a volume named datastore1, mount it to a junction path, and then set the correct export policy. When you attempt to mount the volume from VMware ESXi as a datastore, the server is unable to mount the path /datastore1. You verify that your existing NFS datastore (/datastore0) on the same NetApp storage system SVMis functioning normally.

Referring to the exhibit, what is preventing the server from mounting the new datastore?

The volume is too large to be mounted as an NFS datastore

The load-sharing mirrors need to be updated.

Two volumes cannot be mounted using the same LIF IP address.

The LIF needs to be at its home-port when the volume is mounted.

Valid Netapp NS0-176 Exam Questions and Answers

Valid Netapp NS0-176 Exam Questions and Answers

Share this post

Leave a Reply Cancel reply

Related Posts