Actual Updated Netapp NS0-175 Study Guides

dumps2021-12-20T09:37:42+08:00

Cisco and Netapp Flexpod Design Specialist NS0-175 exam study guides updated version is useful. There are 60 questions in real Netapp certification NS0-175 exam, and you have 90 minutes to complete all the questions. With all of updated NS0-175 exam questions, you will easy to pass the test. Free actual updated Netapp NS0-175 study guides are available below.

Page 1 of 9

1. Which one of the following services is not a service supported by ICAP?

Virus scanning of email content

URL filtering

Active content stripping

Virus scanning of content received through HTT

2. You are working with a customer on a new FlexPod solution. The customer advises you that they want a single point of contact for support issues.

In this scenario, which two support solutions should you offer the customer? (Choose two.)

Cisco SmartNet Total Care

NetApp SupportEdge Expert

NetApp Solution Support for FlexPod

Cisco Solution Support

3. A client has a FlexPod Datacenter solution with four active fabric links in port channel mode established between the Cisco Fabric Interconnects and the IOMs on a Cisco 5108 blade chassis.

The blade chassis is fully populated with Cisco UCS B200M5 blades. A worker in the data center inadvertently unplugs the fourth uplink cable from IOM-A while working in the rack.

In this scenario, what happens to the network traffic?

There is a loss of connectivity for servers 4 and 8.

Traffic is load-balanced within IOM-

Connectivity for servers 3, 4, 7, and 8 all fail over to IOM-

Traffic is load-balanced within IOM-

4. How many disk drives does a C2100 appliance use?

two to seven

one to seven

two to three

one to three

5. How many cluster interconnect switch(es) are required for a 4-node NetApp cluster?

6. Which two statements are correct regarding how the VM-FEX feature extends Cisco fabric technology to a virtual machine? (Choose two.)

The server adapter is divided into a single vNI

VM-FEX ports can operate in 10 different modes.

Each virtual machine includes a dedicated interface on the parent switch.

All virtual machine traffic is sent directly to the dedicated interface on the switch.

7. Refer to the exhibit.

What would be the correct configuration for the ports labeled?

vlan 35fcoe vsan 35int eth1/31channel-group 15 mode activeint eth 1/32channel-group 15 mode activeint portchannel15switchport mode trunkswitchport trunk allowed vlan 35spanning-tree port type edge trunkint vfc15bind interface po15switchport trunk allowed vsan 35vsan databasevsan 35 interface vfc15

vlan 35fcoe vsan 45int eth1/31-32channel-group 15 mode activeint po15switchport access vlan 35int vfc15bind interface po15switchport trunk allowed vsan 45vsan databasevsan 45 interface vfc15

int eth1/31channel-group 15 mode activeint eth 1/32channel-group 15 mode activeint po15switchport mode trunkswitchport trunk allowed vsan 45spanning-tree port type edge trunkvsan databasevsan 45 interface po15

vlan 35fcoe vsan 45int eth1/31-32channel-group 15 mode activeint po15switchport mode trunkswitchport trunk allowed vlan 35switchport trunk allowed vsan 45spanning-tree port type edge trunkvsan databasevsan 45 interface po15

int eth1/31-32channel-group 15 mode activeint po15switchport mode access vsan 45vsan databasevsan 45 interface po15

8. Which of the following options log only reports displays Web request data?

Web Access

Messages

Web Server Acceleration

Web Details

9. NetApp Services include all of the following EXCEPT ______.

Support services

Professional services

System Administration Services

Education

10. Two of the below statements are untrue. Select them.

The Messages log file can be pushed to a remote FTP server at scheduled intervals

The HTTP log file cannot be pushed to a remote HTTPS server at scheduled intervals.

The HTTP log file can be pushed to a remote FTP server in compressed format

The Messages log file cannot be pushed to a remote FTP server in compressed format.

Page 2 of 9

11. When configuring a FlexPod environment for iSCSI boot with Cisco UCS, which item should be preconfigured?

All zoning should be configured

Zonesets should be created

IQN and IP address of target

WWPN Pools

12. Which feature is supported for virtual machines configured with Direct Path I/O using Cisco Virtual Machine Fabric Extender (VM-FEX) distributed switches?

vMotion

Record and Play

Fault tolerance

Unlimited DVS creation per Cisco UCS domain

13. VMware vCenter Server Appliance v6.0 supports which two types of databases? (Choose two.)

MySQL 5.7

Oracle 12c

SQL Server 2016

vPostgres

14. Which of the following TWO statements are FALSE?

The HTTP log file can be pushed to a remote FTP server in compressed format

The Messages log file can be pushed to a remote FTP server at scheduled intervals

The HTTP log file cannot be pushed to a remote HTTPS server at scheduled intervals.

The Messages log file cannot be pushed to a remote FTP server in compressed format.

15. Network Appliance maintains a record of customer product information on the NOW site and this data is ______.

available to anyone with NOW access

only available to NetApp support staff

only available to authorized users

available only during business hours

16. You are designing a new distributed environment of FlexPod systems across the entire organization. You will need to support FlexPod systems in two data centers and FlexPod with Cisco UCS Mini in your five manufacturing plants.

What are two benefits of deploying UCS Central in this scenario? (Choose two.)

It enables management of multiple UCS domains.

It allows consistent configuration of global policies.

It improves the performance of each UCS domain.

It enables a highly available environment.

17. You are sizing a FlexPod Virtual Desktop solution for a customer with 500 virtual desktops in a shared Remote Desktop Services (RDS) topology.

In this scenario, which Cisco best practice should you use?

You should avoid placing more than 20 users per physical host

You should avoid over-committing physical CPU resources for virtual machines

You should avoid changing the virtual host disk queue depth

You should avoid multiple vCPUs per individual virtual machine

18. The best place to find information regarding a log header, such as x-cs-headerlength, is the _____.

Administration Guide

Deployment Guide

Guide to Messages and Logfile Entries

Guide to Caching Protocols and Services

19. Which port type would you configure when you connect a chassis to the Fabric Interconnects?

Fibre Channel storage ports

server ports

appliance ports

Ethernet uplink ports

20. What is the “NTLM Cache” feature typically used for?

Enables NetCache to cache NTLM-authenticated objects.

Enables NetCache to authenticate users using NTL

Enables cached objects retrieved as the result of a successful NTLM exchange to be served to new users without requiring authentication.

Enables the caching and reuse of NTLM challenges in order to reduce the processing load on the domain controller.

Page 3 of 9

21. Which tool may be used to determine the optimal UCS hardware configurations for SAP, Oracle, and Microsoft Enterprise Applications FlexPod solutions?

Microsoft Assessment and Planning (MAP) Toolkit

NetApp Solution Builder

Cisco UCS Sizer for Enterprise Applications

Cisco Resource Comparison Tool

22. What software program manages a NetApp storage controller with Data ONTAP 8.1 or later?

FilerView

OnCommand System Manager

UCS Manager

Web Browser

23. During the design phase of an NFS-only FlexPod environment, the architect wants to ensure that the proposed switch and storage hardware is fully supported within the FlexPod architecture.

Which resource should they consult to confirm support for the design?

NetApp Interoperability Matrix

Config Advisor

FlexPod Technical Specifications

Upgrade Advisor

24. A customer wants a low latency and high IOPS FlexPod solution and decides on an end-to-end NVMe design.

In this scenario, which three components are required to accomplish this task? (Choose three.)

NetApp FAS with a 32Gbps FC HBA

Cisco Application Policy Infrastructure Controller (APIC)

Cisco MDS Series switches

NetApp AFF with a 32Gbps FC HBA

Cisco UCS Virtual Interface Card (VIC) 1400 series

25. What happens when the diag dump command is executed?

A new diagnostics file is created.

The existing diagnostics file is overwritten.

The diagnostics file is automatically sent to NetApp support.

An Autosupport message is generated.

26. Which of the following options best describes what the configure "Shared User Hosts" feature that is found under Appliance Manager's Setup > FTP > Caching Behavior is used for?

a shared IP address that all requesting clients will use to circumvent any authentication or user-specific key requirements on the backend FTP servers

FTP servers from which fetched objects will be cached and served without a user-specific key requirement in order to increase the caching efficiency

a subset of FTP servers that will be accelerated by the NetCache appliance

a subset of FTP servers that can be bound to a shared virtual IP address in order to increase overall caching efficiency

27. Which TWO of the following statements are equivalent?

set config.http.ports “8080 , 8081”

set config.http.ports “8080” “8081”

set config.http.ports \ 8080 \

set config.http.ports // 8080 , 8081 \

28. Which of the following statements best describes what occurs with system messages?

written to a log file that can be pushed to a remote FTP server at scheduled intervals

printed on the console and can be sent in "real time" to a remotesyslog server

written to a log file that can be rotated at any time

written to a log file that can be rotated at scheduled intervals

29. You have a FlexPod solution that consists of a NetApp AFF A800 storage system, a Cisco MDS 9148S switch, and a Cisco UCS 6232 Fabric Interconnect. You want to upgrade NetApp ONTAP software on the AFF A800 to take advantage of a new feature.

In this scenario, which three tools would enable you to verify if the upgrade would be performed safely? (Choose three.)

NetApp Interoperability Matrix Tool

Cisco Intersight

Cisco Data Center Network Manager

Cisco UCS Hardware and Software Compatibility List

NetApp Active IQ Upgrade Advisor

30. Which of the following is an example of a Cisco UCS high availability component?

Clustered fabric interconnects

vMotion

Live migration

Cluster shared volumes

Page 4 of 9

31. Which two support account levels are minimally required when you deploy a FlexPod Datacenter solution? (Choose two.)

NetApp SupportEdge Expert NBD

Cisco SmartNet Total Care 24x7x4

NetApp SupportEdge Advisor 24x7x4

Cisco Solution Support 24x7x4

32. A(n) _____ VIF combines two physical interfaces into a single virtual interface where traffic is active on both physical interfaces.

cluster-mode

multi-mode

single-mode

aggregate-mode

33. You want to provision and back up storage for specific applications in your NetApp FAS environment. You decide to use NetApp Snapshot copies for application-consistent backups.

NetApp SnapDrive and NetApp SnapManager

NetApp SnapDrive and NetApp SnapMirror

NetApp SnapVault and NetApp SnapManager

NetApp Provisioning Manager and NetApp Snap Creator

34. The system messages are _____.

written to a log file that can be rotated at scheduled intervals

printed on the console and can be sent in “real time” to a remote syslog server

written to a log file that can be rotated at any time

written to a log file that can be pushed to a remote FTP server at scheduled intervals

35. Which item is an example of Role-Based Access Control and multi-tenancy support that can be applied to a UCS environment using the Cisco UCS Manager?

Create roles for Data ONTAP Vserver administrators

Create a storage administrator role with control over tasks related to the SAN

Create interface groups on NetApp storage

Apply NFS read/write access to a network share

36. A customer wants to deploy a FlexPod solution that involves directly connecting the NetApp AFF storage using the FCoE protocol to the Cisco UCS Fabric Interconnects.

In this scenario, which Cisco UCS Fibre Channel mode would be used to accomplish this task?

trunk mode

end host mode

switching mode

access mode

37. In which two sources would you verify scale out maximums for NetApp and Cisco UCS environments? (Choose two.)

Cisco Configurations Limits

Cisco UCS Hardware and Software Compatibility List

NetApp Hardware Universe

NetApp Interoperability Matrix

38. According to FlexPod CVDs, what is the recommended MTU size for iSCSI logical interfaces (LIFs) on the NetApp Storage Virtual Machine (SVM)?

1,500

3,000

9,000

9,124

39. A customer wants to add 40 Gbps networking capabilities to a FlexPod Datacenter 10 Gbps environment.

Which two Cisco components support this speed? (Choose two.)

Cisco Nexus 9504

Cisco UCS 1440 VIC

Cisco Nexus 3550-F

Cisco UCS 1455 VIC

40. One of the below ACLs will OK the requests from Engineering groups to www.netapp.com, which one could it be?

allow group "engineering" and server-domain www.netapp.com

allow groupname “engineering” and server-name www.netapp.com

allow group "engineering" and server-name www.netapp.com

allow groupname "engineering" and server-name matches ".netapp.com$"

Page 5 of 9

41. Disk ID is represented in x.y format, where x refers to the _____ and y refers to the _____.

data disk, parity disk

host adaptor, disk ID number

disk ID number, host adaptor

parity disk, data disk

42. A customer is performing a server refresh of their FlexPod solution to accommodate business growth. The customer is interested in using Cisco C-Series servers, and supporting multiple 40 Gbps link to each server, upgrading from the existing 10 Gbps links.

Which two VICs support these requirements? (Choose two.)

Cisco UCS 1480 VIC

Cisco UCS 1497 VIC

Cisco UCS 1495 VIC

Cisco UCS 1440 VIC

43. A customer wants to deploy a FlexPod Datacenter solution in a limited amount of rack space. After planning for the networking and storage devices required for the deployment, they realize they have six rack units of space remaining. They need to install as many servers as possible in this available rack space.

In this scenario, which solution allows them to accomplish their objective?

three Cisco UCS C4200 rack servers

four Cisco UCS B480 M blade servers

six Cisco UCS C220 M5 rack servers

eight Cisco UCS B200 M5 blade servers

44. A customer has reviewed the latest vSphere CVD and asks you if they can use their older Cisco servers in the new FlexPod solution and still have supported configuration.

Which statement is true in this scenario?

FlexPod configurations are fully supported if they follow the technical specifications and compatibility matrices.

FlexPod configurations are fully supported if they follow a specific Cisco Validated Design.

FlexPod configurations are fully supported regardless of the equipment used.

FlexPod configurations are fully supported if they follow a specific NetApp Verified Architecture.

45. Which of the following syntaxes are used to receive extensive help definition for particular commands?

[command] help

command ?

help [command]

46. State whether the following statement is true or false. The sysstat command allows the performance statistics to be viewed, which consists of the present CPU usage, the full amount of network I/O, and the amount of disk I/O.

False

True

47. Which Microsoft Hyper-V and System Center VMM feature allows for creation of multiple VM networks on top of a logical network and allows for tenant use of overlapping IP addresses?

Load Balancer Integration

Network Virtualization

VLAN-based configuration

Stateless Transport Protocol

48. A customer must connect a VMFS datastore for a virtualized application.

Which type of connection should be configured in this scenario?

OpenStack Block Storage Service

NFS VMkernel port

iSCSI VMkernel port

Microsoft iSCSI Host Initiator

49. A customer asks you to design a Red Hat Enterprise Linux OpenStack Platform for pNFS storage. In this scenario, which services driver is required to connect to the customer's NetApp storage?

LVM

NetApp

Ceph

NFS

50. What are three ways to configure a UCS 5108 server chassis power supply? (Choose three.)

n+n redundant

pooled

non redundant

n+1 redundant

grid redundant

Page 6 of 9

51. What is the maximum number of power supplies supported in a Cisco UCS 5108 blade server chassis?

52. A storage architect wants to replace a NetApp 7-mode system with a new NetApp clustered Data ONTAP system.

What are two new features available with this upgrade? (Choose two.)

SnapMirror

junction paths

SnapProtect

namespace

53. A customer needs to replicate NetApp FlexVols in an application agnostic manner for their virtualized and non-virtualized workloads. The customer also needs to migrate between on-prem, NetApp Private Storage (NPS), and ONTAP Cloud instances.

Which NetApp feature satisfies these requirements?

SnapMirror

Load Sharing Mirror

MetroCluster

FlexShare

54. You are designing a new FlexPod-based data center and configuring Virtual Port Channels (vPC) to provide the highest bandwidth throughput, link, and device resiliency to each of your FlexPod systems.

In this scenario, which two statements are true? (Choose two.)

vPCs are required by the FCoE configuration.

vPCs allow a single device to use a port channel across two upstream switches.

vPCs are an industry standard supported by all vendors.

vPCs enable the use of the aggregate bandwidth.

55. A customer is verifying that they have separation on their FC switch fabric to protect their FlexPod solution from their other storage devices.

Which two technologies enable the customer to accomplish this task? (Choose two.)

WWPN zoning

VASN

IQN igroup

VLAN

56. What must be done in order to add a user to the appliance database, which two of the following you must enter?

group

user name

access permissions

password

57. You are designing a FlexPod Express solution based on VMware for a customer that requires both SAN boot and VM datastores up to 100 TB in size.

Which configuration would satisfy the requirements in this scenario?

Boot the server with iSCSI and attach to the datastores using NF

Boot the server with iSCSI and attach to the datastores using iSCS

Boot the server with FlexFlash and attach to the datastores using FCo

Boot the server with FlexFlash and attach to the datastores using NF

58. What is the NetApp recommended bit length that the SSL key should be?

512

768

1024

9216

59. To add a user to the appliance database, you must enter the _____ and the _____.

user name

access permissions

password

group

60. You have multiple clients that want to use FC. You want to ensure that data is kept separate across a FlexPod deployment.

In this scenario, which two constructs would you use to accomplish this task? (Choose two.)

VSANs

FLOGI

VLANs

Storage VMs

Page 7 of 9

61. A customer wants to replace their Cisco UCS 6248UP with the current Cisco UCS 6454. They are currently using six 16 Gbit uplinks per Fabric Interconnect for FC and do not want to change the speed and number of ports used.

In this scenario, what is the minimum number of unified ports that must be configured for FC for a comparable configuration?

62. You want to ass a customer’s NetApp storage controllers into their Cisco Intersight management portal.

In this scenario, which IP address would you choose to add?

NetApp SVM management IP address

NetApp Active IQ Unified Manager IP address

NetApp cluster IP address

NetApp Virtual Storage Console IP address

63. Which traffic through a UCS 6200 cluster can be in Active-Standby mode?

Data traffic only

FHRP

Data and management traffic

Management traffic only

64. An administrator is designing a FlexPod backup solution that includes replication to a remote site that includes the capability to restore to a prior point in time.

In this scenario, which two technologies are required to accomplish this task? (Choose two.)

NetApp SyncMirror

NetApp SnapMirror

NetApp SnapRestore

NetApp FlexClone

65. You are asked to design a new FlexPod solution that will host VMware virtual machines using NFS datastores, file services using SMB, and NFS-mounted home directories. You need to ensure that the network traffic of these three use cases are isolated?

In this scenario, which supported end-to-end network topology would be used to accomplish this task?

VSAN

VXLAN

VLAN

vPC

66. You are asked to ensure link redundancy to your hosts using Virtual Port Channel (vPC).

You are creating a vPC on a pair of Cisco Nexus switches.

In this scenario, which two steps are required to accomplish this task? (Choose two.)

Set all vPC ports to switchport mode access

Configure the vPC peer keep-alive link

Create a vPC domain

Configure system priority

67. You are building a new FlexPod solution and want to verify that you have cabled all the components according to FlexPod design best practices prior to putting your solution into production.

Which tool would you leverage to validate the cabling?

UCS Manager

Config Advisor

Resource comparison tool (RESCOMP)

Solution builder

68. With Data ONTAP 8.1.2, what must be upgraded to the latest firmware to take advantage of the latest updates available for the remote management device?

CPU

Disk Firmware

Service Processor (SP)

Cisco Integrated Management Controller (CIMC)

69. To open a Network Appliance support ticket, you must access ____ at the NOW site.

Submit a RMA

Submit a BURT

Submit a Case

Submit a support ticket

70. You want to ensure optimum Layer 2 latency and performance for server-to-server communications when configuring high availability for bare-metal operating systems.

In this scenario, which action would you perform to accomplish this task?

Ensure that the Fabric Interconnects are in end-host mode; route traffic over the heartbeat link.

Ensure that server-to-server applications use the same fabrics as a primary route.

Provide port-channel connectivity to upstream switching.

Direct connect the Fabric Interconnects with uplink ports.

Page 8 of 9

71. A customer is designing a FlexPod environment and is preparing for an ESXI host installation. High availability is a requirement for the FlexPod design. The ESXI servers will be built with new iSCSI boot LUNs.

Which two NetApp design components are required for this task? (Choose two.)

iSCSI LIF IP addresses

SVM target IQN

boot LUN name

boot LUN UUID

72. State whether the following statement is true or false. The NOW site holds data maintained by the Network Appliance. This information consists of records and customer product information but this data is only available to authorized users.

False

True

73. A customer wants to refresh their FlexPod solution by moving from 10 Gbps to 40 Gbps networking. They use FCoE to boot from SAN.

In this scenario, which statement is true?

FCoE is supported for 32 Gbps adapters

FCoE is supported for 25 Gbps adapters

FCoE is supported for 40 Gbps adapters

FCoE is supported on only 10 Gbps unified adapters

74. What are three capabilities of Config Advisor as it pertains to a FlexPod solution? (Choose three.)

hardware validation

configuration validation

firmware recommendations

firmware download

Hyper-V validation

75. A customer wants to deploy Cisco Intersight into their FlexPod environment. The customer is using the Cisco Intersight SaaS model.

In this scenario, which two virtual machines are required to support this requirement? (Choose two.)

Cisco UCS Fabric Interconnect

NetApp Active IQ Unified Manager

Cisco Intersight Virtual Appliance

NetApp Virtual Storage Console

76. A customer is designing a FlexPod using a 4-node AFF8080EX cluster. The nodes will be cabled to NetApp recommendations.

In this scenario, which switch model would be used for the cluster interconnect network?

NetApp CN1610

NetApp CN1601

Cisco Nexus 5596UP

Cisco Nexus 3048

77. The FlexPod Data Center with VMware vSphere 5.1 solution utilizes vSphere High Availability (HA).

What is a benefit of the vSphere HA feature?

Allocate and balance computing capacity dynamically

Automated restart of virtual machines on other available servers in the case of primary server failure

Continuous availability for applications in the event of server failures by creating a live shadow instance of a virtual machine that is always up to date with the primary virtual machine.

Ensuring zero downtime for all applications

78. An architect is attempting to confirm that all logical interfaces (LIFs) are properly planned with a new clustered Data ONTAP 8.3 implementation. The customer wants to provision NFS datastores across the cluster to allow client access.

In this scenario, which LIF role satisfies this requirement?

data LIF

intercluster LIF

cluster-management LIF

cluster LIF

79. What is the traceroute command used for?

print the route packets take to a network host

display a list of active sockets for each protocol

report interface activity in Kbps

show the state of each interface

80. Under what circumstance can a Cisco Nexus 5548 perform an ISSU (nondisruptive)?

When configured for VPCs

When configured for L3

When an STP-enabled switch is connected downstream

When the STP Bridge Assurance feature is running on a link other than the VPC peer link.

Page 9 of 9

81. FlexPod Datacenter with Cisco UCS Mini supports which Fabric Interconnect model?

6248UP

6332-16UP

6332UP

6324UP

82. Cisco UCS Manager supports which three remote authentication methods? (Choose three.)

NetBIOS

LDAP

WINS

RADIUS

TACACS+

83. What MTU setting should be configured for VMware ESXi VMkernel Ports and Virtual Switches in a FCoE boot from SAN environment?

9000

1500

1492

9216

Actual Updated Netapp NS0-175 Study Guides

Actual Updated Netapp NS0-175 Study Guides

Share this post

Leave a Reply Cancel reply

Related Posts