Check Point 156-835 Exam Updated Questions

dumps2023-02-18T01:35:51+08:00

Earning the Check Point Certified Maestro Expert Exam 156-835 certifications can be a great way to boost your career in the cybersecurity industry. By using 156-835 updated practice questions, you can feel confident in your ability to succeed on the exam and demonstrate your knowledge and expertise in managing Check Point Maestro. Whether you choose to use resources from Check Point or a third-party provider, be sure to choose a reputable source that has a track record of success. Free Check Point 156-835 exam updated questions are below.

Page 1 of 2

1. What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?

Reserved for internal purposes. Not in use.

Out-of-band interfaces for access to Orchestrator itself.

1Gbps connectivity for Security Groups.

Additional ports used as uplinks.

2. What is a Security Group?

Logical group of computer and network resources

Group of security administrators

Group of security gateways

Group of appliances with enabled NGTX software blades

3. Orchestrator should be defined in SmartConsole as:

Orchestrator is not defined in SmartConsole

Check Point host

Security Gateway

Host

4. What kinds of transceivers are supported on Orchestrator MHO-170?

QSF

QSFP28

SFP+. SFP28

SFP+, SFP28. QSFP

QSFP, QSFP28

5. What does the lldpctl command do?

Show all devices discovered by LLDP protocol on downlink ports

Discover orchestrators

Show all devices discovered by LLDP protocol on uplink ports

Show all devices discovered by LLDP protocol on all ports

6. One single Appliance supports 1M concurrent connections.

How many concurrent connections will support Security Group of 2 Appliances?

500K

7. What cannot be learned from the output ofasg monitorcommand?

Appliances cluster status

Port status

Uptime

Security Policy status

8. What command should be used for collecting diagnostic information about the orchestrator?

cpinfo

orch_info

cpview

asg pert -v

9. What is a downlink interface used for?

To connect Orchestrators to customer's infrastructure

To connect appliances to customer's infrastructure

To connect appliances to Orchestrators

To connect in between Orchestrators

10. Splitter cannot be used __________.

To connect single port on orchestrator to multiple Appliances

To connect single port on Appliance to multiple ports on the orchestrator

To connect single port on orchestrator to the same Appliance

To connect single port on orchestrator to multiple port on external switch

Page 2 of 2

11. There's a 23800 appliance with quad NIC in slot 5.

What would be the name of port 3 on this NIC?

ethBP3-05

ethsBP5-03

ethsBP3-05

ethsBP-05

12. Which licenses should be issued for the Orchestrator?

No licenses are required for Orchestrator

The Orchestrator is considered a Management server, hence it's licensed the same way

The Orchestrator requires NGTX license

Depends on Software Blades enabled on connected appliances

13. Browse to the Orchestrator’s WebUI

3-4-2-6-5-7-1

3-1-7-2-4-6-5

1-4-2-5-7-3-6

7-4-2-5-3-1-6

14. What is the Iterator process?

Iterator is the process that simulates distribution in case of Appliance failure

Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive

Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure

Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery

15. What does the command'g_all' do?

It's followed by other command and execute it on all active Appliances within Security Group

It's followed by other command and execute it on all Appliances connected to Orchestrator

Switches all Appliances to Global mode

Bring up all Appliances

Check Point 156-835 Exam Updated Questions

Check Point 156-835 Exam Updated Questions

Share this post

Leave a Reply Cancel reply

Related Posts