Free D-NWG-FN-23 Dell Networking Foundations 2023 Exam Dumps

dumps2023-10-19T11:52:27+08:00

D-NWG-FN-23 Dell Networking Foundations 2023 exam is much hot among those DELL candidates. The D_NWG-FN-23 exam basic information is available below for you to study. There are 60 questions in the real Dell Networking Foundations 2023 D-NWG-FN-23 exam, and you have 90 minutes to answer all the questions. The passing score is 60%. We have cracked the latest D-NWG-FN-23 exam dumps, which are valuable in your preparation. Free Dell Networking Foundations 2023 D-NWG-FN-23 exam dumps are below.

Page 1 of 7

1. At which layer of the OSI model is the Rapid Spanning Tree protocol used to prevent switching loops?

Physical

Network

Data Link

Transport

2. Which parameter is required to match an OSPF Adjacency to form?

IP addresses

Area ID

Switch models

Switch firmware version

3. A Dell Networking N3024 has a link aggregation configured as shown:

interface Gi1/0/1

channel-group 1 mode active

exit

!

interface Gi1/0/2

channel-group 1 mode active

exit

!

interface port-channel 1

switchport access vlan 10

exit

After connecting all cables, the port-channel does NOT work as expected.

As part of the troubleshooting process, the technician examines the “show lldp” displayed:

What is the most likely cause for the issue on the port-channel?

The interface port-channel is not using 10Gbps interfaces.

The interfaces on the N2024 switches are running LAC

The interface port-channel is not configured in trunk mode.

The interfaces are connected to different switches.

4. A technician configures RIP on a new N-Series switch to connect to an existing switch that runs RIP. The routing table is not populating even after the network statements are added.

What is a possible cause of this issue?

The existing switch has not been configured with the command “hostroutesaccept”.

The new switch’s interface is in the wrong subnet to form a RIP relationship.

The “ip helper-address” command has not been configured on the existing switch.

The other switch is not a root bridge and cannot form an RIP relationship.

5. Which of the following is an optional LLDP TLV?

Chassis ID

System Name

Port ID

Time-to-live

6. A network administrator needs to identify which MAC addresses are static.

Under which column in the output of the show mac-address-table command is this information displayed?

Interface

Type

MAC address

State

7. What is the FCS field used for in an Ethernet frame?

Redirect ICMP messages back to the originator

Ensure the frame was not corrupted during transmission

Resolve ARP requests

Look up the destination address

8. What is the size of the ICMP header?

8 bits

8 bytes

16 bits

16 bytes

9. Which two port states are valid on a root bridge in a converged Spanning Tree network? (Choose two.)

Blocking

Designated

Forwarding

Listening

Alternate

10. What is the dotted decimal notation for a /29 prefix?

255.255.255.192

255.255.255.252

255.255.255.240

255.255.255.248

Page 2 of 7

11. What is the maximum frequency of a CAT6 UTP cable?

100 MHz

250 MHz

500 MHz

600 MHz

12. When configuring a switch, which CLI mode only supports limited show commands?

EXEC

Maintenance

Configuration

EXEC Privilege

13. Which command sequence leads to the successful creation of a Layer 3 port channel on an OS10 switch?

1(config-if-po-2)# ip address 192.168.0.0/31 S1(config-if-po-2)# no switchport

S1(config-if-po-2)# ip address 192.168.0.0/31 S1(config-if-po-2)# no switchport

S1(config-if-po-2)# ip address 192.168.0.0/31 S1(config-if-po-2)# switchport mode IPv4

S1(config-if-po-2)# no switchport S1(config-if-po-2)# ip address 192.168.0.0/31

14. Which type of route is often used to direct traffic bound for the Internet?

Redistributed

Directly connected

Dynamic

Default

15. How is a switch different from a hub?

A switch operates at a lower, more efficient layer of the OSI model.

A switch decreases the number of broadcast storms.

A switch tracks MAC addresses of all connected devices.

A switch does not include any latency into the frame transfer time.

16. Which IEEE standard defines the Data Link Layer, Discovery protocol?

802.1AB

802.1AX

802.1D

802.1W

17. What does the blinking yellow Activity/PoE LED indicate on an N-Series switch?

There is no current transmit/receive activity and PoE power is off.

There is no current transmit/receive activity and PoE power is on.

There is current transmitting/receiving and PoE power is on.

There is current transmitting/receiving and PoE power is off.

18. On which Dell EMC Networking switches can Multi-Chassis Link Aggregation (MLAG) be configured?

C9000 Series

N-Series

S-Series

Z-Series

19. A Dell EMC Networking N-Series switch is configured on a port channel with LACP using the interfaces Te1/0/1 and Te1/0/2.

How is the egress traffic distributed among the interfaces?

Traffic overflow will be sent to the second interface

Interfaces will be used in active/passive

Load balanced per packet using round robin

Load balanced using a hash function

20. Which IPv6 scope is used for private addressing within an organization?

APIPA

Area wide

Global

Unique local

Page 3 of 7

21. Which Border Gateway Protocol (BGP) version supports IPv6?

BGPng

BGPv2

BGPv3

BGPv4

22. Which IPv6 address type is similar to IPv4 APIPA?

Multicast

IPv6 link-local

Global unicast

Unique Local

23. What attributes does LLDP use to send and receive information about directly connected neighbors?

Unit Header Value

Type Length Value

Unit MAC Frames

Packets Frames Headers

24. What is the correct sequence of steps that occur in the communications between the client and server to obtain an IP address from a DHCP server?

25. Which OS6 command is used to verify the running configuration on port 4?

# show running-config int eth 1/0/4

# show running-config int gi 1/0/4

# show running-configuration int gi 1/1/4

# show running-configuration interface ethernet 1/1/4

26. A network administrator created three VLANs on an Ethernet switch.

How many broadcast domains are created by the switch?

27. Refer to the exhibit.

A technician configures RIP on a new N-Series switch to connect to an existing switch that runs RIP. The new switch routing table is NOT populating even after the correct network statements are added.

What is causing this issue?

The new N-Series switch does not have “default-information originate” configured.

The existing switch has been configured for “hostroutesaccept”.

The other switch is a root bridge and cannot form RIP relationships.

The existing switch is configured to send and receive only for RIPv1.

28. How is outbound traffic distributed when using LACP port channels on OS6 switches?

Load balanced per packet using round robin

Interfaces are used in active/passive

Load balanced using a hash function

Traffic overflow is sent to the second interface

29. A static route is denoted with which flag in the routing table?

30. A network administrator has a Dell EMC switch that has been configured with several VLANs. Each VLAN switch virtual interface (SVI) has an IP address assigned to it with each of them on different subnets. In addition, routing has been enabled on the switch.

Which action occurs when the switch receives a packet on one of its SVIs but the destination IP address of the packet does not match the IP address of that SVI?

Switch checks its routing table and forwards the packet accordingly.

Switch duplicates the packet and sends it to all interfaces.

Switch replies back to the source with an ICMP Reject packet.

Switch drops the packet.

Page 4 of 7

31. Which type of domains are connected by a Layer 2 switch?

Single collision domain and a single broadcast domain

Multiple broadcast domains and multiple collision domains

Multiple collision domains and a single broadcast domain

Single collision domain and multiple broadcast domains

32. Which command is available in OS6 to verify jumbo frames?

show interfaces counters

show hardware drops

show interface flowcontrol

show interfaces config

33. What accurately describes IPv6 addressing?

IPv6 addresses are denoted by eight groups of four hexadecimal numbers.

IPv6 uses 128 hexadecimal numbers instead of the 32 hexadecimal numbers used by IPv4.

IPv6 is used to converse IP addresses and utilize private addresses.

IPv6 uses broadcast addresses for neighbor discovery.

34. A dell Networking N-Series has configured a port-channel with LACP using the interfaces Tel/0/1 and Tel/0/2.

How is the egress traffic distributed among the interfaces?

Load balanced using a hash function

Load balanced per packet using Round Robin

Traffic overflow will be sent to the second interface

Interfaces will be used in active/passive

35. Which route type is added to the routing table by a routing protocol?

Default route

Dynamic

Static

Directly connected

36. Which nanometer range will an SFP work in multi-mode?

850

1310

1510

1610

37. Which operating system does an N-Series switch use?

OS 3

OS 6

OS 9

OS 10

38. A service technician is deploying four Dell N-Series switches in a company's network. The technician has enabled the spanning tree protocol on the switches.

Which switch would the spanning tree protocol select as a root bridge?

22-33-44-55-66-77 : 32768

11-22-33-44-55-66 : 36864

22-33-44-55-66-78 : 32768

11-22-33-44-55-65 : 32768

39. Which formula is used for calculating OSPF interface costs?

Reference bandwidth C interface bandwidth

Reference bandwidth / interface bandwidth

Reference bandwidth + interface bandwidth

Interface bandwidth / reference bandwidth

40. What are the required commands to configure a native VLAN of 10 and a tagged VLAN of 20 on an OS6 switch?

# interface ethernet 1/6 # switchport trunk encapsulation dot1 # switchport trunk native vlan 10 # switchport trunk allowed vlan 20 # switchport mode trunk

# interface gigabitethernet 1/0/6 # switchport mode trunk # switchport mode allow vlan 20 # switchport mode trunk native vlan 10

# interface ethernet 1/1/6 # switchport mode trunk # switchport trunk allowed vlan 20 # switchport access vlan 10

# interface gigabitethernet 1/0/7 # switchport mode trunk # switchport mode allow vlan 20 # switchport mode trunk native vlan 10

Page 5 of 7

41. A network technician has printers that negotiate at half-duplex.

Which three switches will auto-negotiate the printers? (Choose three.)

X1026

N2048

X1008P

N3024P

N1548

N2048P

42. What are three benefits of using dynamic routing protocols over static routing? (Choose three.)

Can be implemented with one command to produce routes in the RIB

Lower administrative distance compared to static routes

Automatically adapts to changing topology to provide alternative paths

Is easier to troubleshoot over static routes in the event of a failure

Less overall administration, management, and maintenance of the routing table

Is scalable to very large multi-router, multi subnet networks

43. Refer to the output shown:

Which two statements describe the state of configuration of interfaces gi1/0/1-24? (Choose two.)

The interfaces are administratively Down.

Spanning tree is NOT blocking any interfaces.

The interfaces have negotiated to mode trunk.

The interfaces are in access mode VLAN 1.

The interfaces are administratively Up.

44. Two N3024F switches are directly connected using 10GBASE-SR transceivers and 10 foot fiber patch cables. The ports on both sides are NOT linking.

What are two possible reasons for this issue? (Choose two.)

The fiber connectors are inverted.

The transceivers are on SFP ports.

The fiber length is too short.

The connection is using multimode fiber.

The fiber is unidirectional.

45. What accurately describes an ICMP error message?

ICMP error message will be generated for a datagram having a multicast address

ICMP error message will not be generated for a datagram having an address of 127.0.0.0

ICMP error message will be generated for a fragmented datagram that is not the first fragment

ICMP error message will be generated in response to a datagram carrying an ICMP error message

46. What is the default OSPF “hello interval”?

5 seconds

10 seconds

15 seconds

30 seconds

47. A network administrator wants to use a subnet that will only have two host addresses.

Which subnet mask meets this requirement?

255.255.255.248

255.255.255.252

255.255.255.254

255.255.255.256

48. Which platforms are supported by the Dell EMC Networking OS (DNOS) 6?

N1500 Series switch and N2000 Series switch

N1700 Series switch and N1500 Series switch

N1700 Series switch and N3500 Series switch

N3500 Series switch and N2000 Series switch

49. Which switch should Spanning Tree Protocol choose to become the root bridge in the election process?

22-33-44-55-66-78 : 32768

11-22-33-44-55-66 : 36864

22-33-44-55-66-77 : 36864

11-22-33-44-55-65 : 32768

50. In addition to receiving an IP address, what other information is obtained from a DHCP server?

Default gateway address and VLAN ID

DNS server address and port speed

Default gateway address and DNS server address

DNS server address and VLAN ID

Page 6 of 7

51. Which IP address belongs to the same subnet as 192.168.8.10/22?

192.168.1.192

192.168.5.16

192.168.10.1

192.168.0.3

52. If a packet is sent to an IPv6 address and many devices receive the packet, what is this type of traffic?

Multicast

Broadcast

Anycast

Unicast

53. Which field of the 802.3 frame is used by network interface cards to synchronize their receivers?

Start frame delimiter

Preamble

Cyclic redundancy check

Frame check sequence

54. Which Layer 2 technology is used to segment a switched network?

Trunking

ISL

LAN

VLAN

55. How many total addresses for network, broadcast, and host are provided with the subnet mask 255.255.255.240?

56. A technician implements a new copper connection to Gi2/0/20.

Which command should be used to check the cable length?

test tdr copper-length gigabitethernet 2/0/20

test copper-length tdr gigabitethernet 2/0/20

test tdr copper-port gigabitethernet 2/0/20

test copper-port tdr gigabitethernet 2/0/20

57. Which Layer 1 device can be used to enlarge the area covered by a single LAN segment?

Router

Repeater

Switch

NIC

58. A technician has one stack of three N3024. The technician removes the master unit without powering off the stack. This unit is reconfigured with new IP address in the same Layer 2 network.

Which management issue is the result?

A duplicate MAC address

A duplicate IP address

Lost switch configuration

A switch that flashes red LED

59. Refer to the output:

How has OSPF been configured?

For network type broadcast

With a dead-timer mismatch

For network type point-to-point

With a Peer-to-Peer LSA learning of type 7 LSAs

60. A technician wants to allow SSH connections to authenticate using an external server. If the external server becomes unreachable, the users created on the switch should be allowed.

What command will accomplish this goal?

AAA authentication login default radius local

AAA authentication ssh default radius enable

AAA authentication login default local radius

AAA authentication ssh default radius none

Page 7 of 7

61. What is the correct sequence of steps when a web browser accesses a web server?

62. Which subnet mask provides only two valid IP addresses that can be assigned to hosts?

255.255.255.248

255.255.255.254

255.255.255.252

255.255.255.256

63. What are the Protocol Data Units (PDUs) called at the Transport layer?

Data Payload

Frame

Segment

Packets

64. Which network device functions only at Layer 1 of the OSI model?

Switch

Bridge

Hub

Router

65. What accurately describes the Simple Network Time Protocol (SNTP)?

Time synchronization algorithms are more complex and account for clock drift

Implemented on a Dell EMC Network OS 9 and OS 10

SNTP devices can act as both clients and servers

Client makes sudden changes to adjust the time

66. In IPv6 addressing, what refers to four binary characters?

Byte

Bit

Nibble

Block

67. Which command is used to prevent STP learning on a port that is connected to a server?

#able spanning-tree

#spanning-tree security

#spanning-tree portfast

#spanning-tree off

Free D-NWG-FN-23 Dell Networking Foundations 2023 Exam Dumps

Free D-NWG-FN-23 Dell Networking Foundations 2023 Exam Dumps

Share this post

Leave a Reply Cancel reply

Related Posts