Aruba Certified Mobility Associate Exam HPE6-A70 Study Guides

dumps2022-01-22T02:18:46+08:00

Aruba Certified Mobility Associate exam HPE6-A70 test study guides are helpful in your preparation. Reading HP certification HPE6-A70 exam information first to study. In real HPE6-A70 exam, there are 60 questions, and you have 90 minutes to complete the test. The required passing score of HP HPE6-A70 exam is 70%. Free HP Certification HPE6-A70 exam study guides are available below.

Page 1 of 4

1. A company has an Aruba solution. A network administrator wants to prevent wireless users from accessing shopping web sites with a bad reputation.

What should the administrator set up to deny such traffic?

an AppRF engine

application filters in the Traffic Analysis dashboard

firewall access control rules that specify HTTP and HTTPS services

firewall application rules

2. What is a reason for a company to choose to deploy an Aruba 7024 Mobility Controller (MC) rather than an Aruba 7010 MC?

to support 802.11ac Aps rather than only 802.11n APs

to support more wireless users

to support more POE devices directly connected to the MC

to support a faster firewall throughput rate

3. What is a key difference between an Aruba Air Monitor (AM) and an Aruba Spectrum Analyzer (SA)?

An AM detects threats such as rogue APs, while an SA analyzes RF conditions.

An AM detects rogue APs and provides data services to clients, while an SA only detects rogue APs.

An AM scans on only one 802.11 frequency band, while an SA scans on both 802.11 frequency bands.

An AM both detects wireless intrusion attempts and mitigates them, while an SA only detects wireless intrusion attempts.

4. An AP operates on channel 6.

Which device causes the most significant and consistent interference with the signal?

cellular phone

weather radar

wireless security camera operating on channel 8

AP operating on channel 11

5. Refer to the exhibits.

Exhibit 1

Exhibit 2

A network administrator configures a guest WLAN on an Aruba Mobility Master (MM)-based solution. The exhibits show some of the settings for this WLAN.

Which settings must the administrator configure on each Mobility Controller (MC) at the device level for this configuration to function properly?

an IPsec preshared key

CPSec certificates

a portal page

VLAN 99 IP settings

6. What is an advantage for a network administrator to use AirWave over a Mobility Master (MM)?

ability to gather and analyze historical user data, and monitor client association and network usage trends

scans wireless client settings and brings those settings in compliance with corporate security policies.

ability to monitor and manage a Mobility Controller (MC) to configure the WLAN

provides realtime firewall hits for client network troubleshooting

7. Which deployment option for Aruba Controllers is new to ArubaOS 8?

deployment as virtual appliances

deployment in standalone mode

deployment in master-local mode

deployment as branch office controller

8. A company has a single Aruba Mobility Master (MM)-based solution with two Mobility Controllers (MCs). Network administrators want APs in building 1 to support a WLAN but do not want APs in building 2 to support the WLAN.

How can administrator ensure that they can enforce this rule as they set up the WLAN in the Mobility Master (MM) Interface?

Place APs in different buildings in different AP Groups.

Assign APs in different buildings to different MM nodes.

Configure APs in different buildings to use different frequency bands.

Assign different radio profiles to APs in different buildings.

9. A network administrator configures this policy:

Users to which this policy applies are unable to receive IP addresses with DHCP.

How should the administrator fix the issue?

Change user to any in the user any svc-dhcp permit rule.

Move the user any svc-dhcp permit rule to the bottom of the list.

Remove the deny rule from the policy.

Use the correct service alias in the user any svc-dhcp permit rule.

10. A network administrator reduces an AP radio transmit power from 18 dBm to 15 dBm. This is a loss of 3 dBms.

What is the current power as a percentage of the original power?

10%

33%

50%

83%

Page 2 of 4

11. What are two criteria that distinguish different Aruba Mobility Controller (MC) models from each other?

firewall speed and ability to act as a standalone controller or not

number of supported users and firewall throughput

number of supported APs and ability to support 802.11ac APs or not

number of supported users and ability to support 802.11ac APs or not

12. A network administrator has installed PEF licenses in the global pool of a Mobility Master

(MM) solution. When the administrator tries to configure roles and policies, an error indicates that the PEF licenses must be installed.

What should the administrator do to correct this issue?

Ensure the PEF licenses were installed at the Managed Network and not at the MM level.

Enable Building 1 as a local license pool.

Enable the PEF feature in the Global Usage window.

Activate the PEF licenses through an Aruba Activate account.

13. A network administrator creates the role employees and adds the rule to it:

user any any permit

The first several wireless clients assigned to the employees role are assigned IP addresses in the 10.10.10.0/24 subnet. Several other wireless clients with the employees role are then assigned IP addresses in the 10.10.20.0/24.

When the Aruba firewall matches traffic from these clients to the user any any permit rule, what does it do?

It drops traffic from wireless clients in both the 10.10.0/24 subnet and 10.10.20.0/24 subnet.

It permits traffic from wireless clients in both the 10.10.10.0/24 and 10.10.20.0/24 subnet as long as the packet has a source I

It permits the traffic from wireless clients in the 10.10.20.0/24 subnet, but drops the traffic from wireless clients in the 10.10.10.0/24 subnet.

It permits the traffic from wireless clients in the 10.10.0/24 subnet, but drops the traffic from wireless clients in the 10.10.20.0/24 subnet.

14. A network administrator examines a list of 2.4GHz clients with low performance in the Mobility Master (MM) dashboard.

Which property for a client should pose a concern as a potential performance issue?

Radio PHY of HT 20MHz

Max speed of 72Mbps

SNR of 18

Usage of 10 MB

15. What is the minimum space between channels in the 2.4GHz range to prevent overlap?

1 channel

3 channels

5 channels

7 channels

16. What is an example of a Layer2 wireless threat that a wireless intrusion detection system (WIDS) should detect?

802.11 association floods

RF jamming

Bluetooth interference

spyware

17. Refer to the exhibit.

A network administrator sets up the Exam_Employees WLAN on an Aruba solution with a default role of guest, as shown in the exhibit.

To which users does the guest role apply?

users who successfully authenticate and are assigned to the default role by the RADIUS server

users who successfully authenticate and are not assigned a different role by the RADIUS server

users who have connected to the SSID, but have not yet attempted authentication

users who fail authentication

18. A network administrator wants to assign an authentication server group to the WPA2-Enterprise WLAN.

Which profile should the administrator modify?

Virtual AP

SSID

AAA

L2 Authentication

19. If the decrypt-tunnel forwarding mode is selected in an employee WLAN, where is the user traffic decrypted?

at the switch

at the AP

at the controller

at the RADIUS server

20. An Aruba Mobility Master (MM)-based solution has a WLAN that uses WPA2-Enterprise security. A test login on a wireless client fails.

How can a network administrator determine whether the RADIUS server rejected the credentials or another issue occurred?

View Technical Support information for the M

Ping the IP address configured as the RADIUS server.

Use the MM AAA Server Test Diagnostic tool.

Use the tools in the MM Dashboard > Security window.

Page 3 of 4

21. A company has an Aruba Mobility Master (MM)-based solution. Under which circumstance will an AP radio change channel without the use of the Mobility Master (MM)?

when the MM detects that a different channel has significantly better quality

when the Mobility Controller (MC) detects a rogue AP on the channel

when the AP detects a large amount of interference on its channel

when the Client Match rules indicate that nearby clients do not support the current channel

22. Refer to the exhibit.

What is a valid way to help the APs discover devices that can control them?

Set up an Aruba Central subscription, and ensure that APs can reach the Internet.

Enable CPSec, and ensure the Mobility Master (MM) and Mobility Controllers (MCs) trust the Aruba certificates installed on the APs at the factory.

Specify the Mobility Master (MM) IP address in DHCP option 43 on the network DHCP server.

Map the Mobility Controller (MC) IP addresses to the aruba-master name on the network DNS server.

23. A company has an Aruba Mobility Master (MM)-based solution. A network administrator wants to collect and analyze information about clients and access points (APs) over extended periods of time.

What should the administrator do to achieve this goal?

Add Aruba AirWave to the solution.

Run a Traffic Analysis report on the M

Make sure that MM has sufficient AppRF licenses.

Enable archival from the MM interface Maintenance windows.

24. A network administrator creates a user account on an Aruba Mobility Master (MM) with the guest-provisioning role.

Which task does this user have the rights to perform?

set up portal pages

create guest user accounts

monitor guest clients

create guest WLANs

25. What is a role fulfilled by an Aruba Mobility Master (MM)?

It forwards and routes traffic for wireless users across multiple sites.

It terminates control tunnels for Aruba APs.

It provides an advanced Web portal for onboarding Bring Your Own Device (BYOD) devices.

It manages VLAN and routing configuration for multiple Mobility Controllers (MCs).

26. An Aruba solution runs ArubaOS 8 and uses a mobility master architecture.

Which feature can network administrators use to balance wireless devices across APs on different channels?

AirMatch

Client Match

AppRF

ARM

27. Refer to the exhibit.

The exhibit shows output from a Mobility Master (MM) dashboard.

What is a valid reason for the administrator to click the akamai square under applications?

to see the break down for only the roles, destinations, WLANs, and devices that use this application

to download a report about the usage of this application over time

to create filter rules in order to control wireless user access to this application

to set up bandwidth rule in order to control wireless user access to this application

28. A company has a Mobility Master (MM)-based solution. A network administrator wants to monitor data transfer speed ranges of all currently connected clients.

Which dashboard page in the MM interface should the administrator visit?

Security

Performance

Traffic Analysis

Network

29. A company has a Mobility Master (MM) solution that manages Mobility Controllers (MCs) in several groups. The company has several WebCC licenses and wants to reserve these licenses for MCs in the Sunnyvale group only.

How can a network administrator achieve this goal?

Associate the MAC addresses for the Sunnyvale MCs with the licenses when they are generated.

Make sure to be at the Managed Network > Sunnyvale level in the MM Interface when the licenses are installed.

Install the licenses on the MM, and allocate them to a dedicated local pool for the Sunnyvale group.

Install the licenses directly on the MCs in the Sunnyvale group, and activate the licneses locally.

30. A company deploys an Aruba wireless solution for the first time. In which deployment is clustering supported?

deployment as Mobility Masters (MMs)

deployment as a standalone VMC

deployment in 7000 Series standalone mode

deployment in master-local mode

Page 4 of 4

31. Refer to the exhibit.

What describes the behavior for this WLAN?

APs in the default group broadcast the SSI

Clients can connect to the WLAN on APs in the default group only.

No APs broadcast the SSI

Clients cannot connect to the WLAN until administrators activate it.

No APs broadcast the SSI

Clients can connect to the WLAN on APs in the default group only.

APs in the default group broadcast the SSI

Clients can connect to the WLAN on APs in any group.

32. What is a valid way to deploy an Aruba Mobility Master (MM)?

as a subscription-based service through the Aruba cloud

as a role on a Mobility Controller 7030 that is deployed as a standalone controller

as a virtual appliance on a server that meets the recommended hardware requirements

as a role on a Mobility Controller 7240 that is deployed as a master controller

33. What is one difference between captive portal authentication and 802.1X authentication?

802.1X authentication always authenticates the wireless client, while captive portal authentication always authenticates the wireless user.

802.1X authentication occurs at Layer 2, while captive portal authentication occurs at Layer 3.

802.1X authentication must use an LDAP server, while captive portal authentication can use a RADIUS server or an LDAP server.

802.1X authentication is typically implemented without encryption, while captive authentication is often combined with WPA or WPA2.

34. A network administrator needs to configure firewall rules for three roles:

✑ Finance

✑ Sales

✑ Employee

Several rules apply to both the Employee and Sales roles, but not to the Finance role.

What is the simplest way to configure these rules?

Define the Employee and Sales roles as internal roles, and then configure the rules as global rules for internal users.

Apply these rules as a subnet-based policy, and then ensure that only Employee and Sales users are assigned IP addresses in that subnet.

Select either the Employee or Sales role, and then configure these rules within the global policy.

Create a policy with these rules, and then apply that policy to the Employee and Sales roles.

35. Refer to the exhibit.

A network administrator creates a guest WLAN on an Aruba Mobility Master (MM). The exhibit shows some of the settings for the WLAN.

How should the network administrator handle the Auth server settings?

Add an authentication server with the LDAP type and the IP address of the company AD server.

Add an authentication server with the LDAP type and IP address 10.10.10.10.

Add an authentication server with the RADIUS type and IP address 10.10.10.10.

Add an authentication server with the RADIUS type and the IP address of the company AD server.

36. Refer to the exhibit.

A network administrator needs to use Aruba AirWave to view statistics for an AP’s 802.11ac radio.

How can the administrator update the information on-demand rather than wait the typical interval?

Click Poll Controller Now

Click the 802.11ac link

Log out of the interface and log back in

Refresh the browser

37. A customer has a large campus that requires 400 Aruba 335 APs to support a total of 20,000 wireless users and 12Gbps of traffic. Although the customer wants two controllers for redundancy, each controller must be able to support all of the APs and users on its own.

Which Aruba Mobility Controller models meet the customer requirements and DO NOT unnecessarily exceed them?

Aruba 7024 controllers

Aruba 7210 controllers

Aruba 7240 controllers

Aruba 7030 controllers

38. A company currently uses Instant APs (IAPs), all managed by a virtual controller. The company expects to double in size without the next 18 months. The network manager wants to purchase additional APs to service the increased traffic load. The network manager also wants to deploy a Mobility Controller (MC) to manage all APs.

How should the network administrator adapt the current IAPs to a controlled architecture?

Manage both the MCs and IAP clusters with Aruba Central.

Configure the IAPs to establish CPSec tunnels to the new MCs.

Manage both the MCs and IAP clusters with a Mobility Master (MM).

Convert the IAPs to Campus APs controlled by the new MCs.

39. A company plans to deploy a Mobility Master (MM). The MM will manage 50 Mobility Controller (MC) appliances that will control a total of 700 APs, and 10 Virtual Mobility Controllers (VMCs) that will control a total of 200 APs.

How many MM licenses does the company require?

210

900

960

40. When an Aruba solution uses AirMatch, which device generates the channel and power plan for an AP?

the AirWave Management Platform

the Mobility Master (MM)

the Mobility Controller (MC) for the AP

the AP itself

Aruba Certified Mobility Associate Exam HPE6-A70 Study Guides

Aruba Certified Mobility Associate Exam HPE6-A70 Study Guides

Share this post

Leave a Reply Cancel reply

Related Posts