Good Updated Questions for CompTIA Network+ N10-008 Test

dumps2023-01-14T01:48:41+08:00

CompTIA Network+ N10-008 test updated questions are valuable in the preparation. CompTIA Network+ exam N10-008 is designed to test a candidate’s knowledge and skills in installing, configuring, and troubleshooting various network technologies. The exam covers a wide range of topics, including network architecture, protocols, topologies, and security.

Therefore, a candidate should use a variety of study materials to prepare for the N10-008 exam, including updated exam questions, official CompTIA training courses, and hands-on experience with networking technologies. It is also recommended that candidates stay up-to-date with any changes or updates to the N10-008 exam.

Page 1 of 12

1. A systems administrator needs to improve WiFi performance in a densely populated office tower and use the latest standard. There is a mix of devices that use 2.4 GHz and 5 GHz.

Which of the following should the systems administrator select to meet this requirement?

802.11ac

802.11ax

802.11g

802.11n

2. A network administrator is designing a new datacenter in a different region that will need to communicate to the old datacenter with a secure connection.

Which of the following access methods would provide the BEST security for this new datacenter?

Virtual network computing

Secure Socket Shell

In-band connection

Site-to-site VPN

3. Which of the following connector types would have the MOST flexibility?

SFP

BNC

RJ45

4. Which of the following would be BEST to use to detect a MAC spoofing attack?

Internet Control Message Protocol

Reverse Address Resolution Protocol

Dynamic Host Configuration Protocol

Internet Message Access Protocol

5. Which of the following technologies provides a failover mechanism for the default gateway?

FHRP

LACP

OSPF

STP

6. A technician is installing a new fiber connection to a network device in a datacenter. The connection from the device to the switch also traverses a patch panel connection.

The chain of connections is in the following order:

Device

LC/LC patch cable

Patch panel

Cross-connect fiber cable

Patch panel

LC/LC patch cable

Switch

The connection is not working. The technician has changed both patch cables with known working patch cables. The device had been tested and was working properly before being installed.

Which of the following is the MOST likely cause of the issue?

TX/RX is reversed

An incorrect cable was used

The device failed during installation

Attenuation is occurring

7. An IT organization needs to optimize speeds for global content distribution and wants to reduce latency in high-density user locations.

Which of the following technologies BEST meets the organization’s requirements?

Load balancing

Geofencing

Public cloud

Content delivery network

Infrastructure as a service

8. A network administrator walks into a datacenter and notices an unknown person is following closely. The administrator stops and directs the person to the security desk.

Which of the following attacks did the network administrator prevent?

Evil twin

Tailgating

Piggybacking

Shoulder surfing

9. A new cabling certification is being requested every time a network technician rebuilds one end of a Cat 6 (vendor-certified) cable to create a crossover connection that is used to connect switches.

Which of the following would address this issue by allowing the use of the original cable?

CSMA/CD

LACP

PoE+

MDIX

10. Which of the following is used to track and document various types of known vulnerabilities?

CVE

Penetration testing

Zero-day

SIEM

Least privilege

Page 2 of 12

11. A technician needs to configure a Linux computer for network monitoring.

The technician has the following information:

Linux computer details:

Switch mirror port details:

After connecting the Linux computer to the mirror port on the switch, which of the following commands should the technician run on the Linux computer?

ifconfig ecth0 promisc

ifconfig eth1 up

ifconfig eth0 10.1.2.3

ifconfig eth1 hw ether A1:B2:C3:D4:E5:F6

12. A network administrator needs to query the NSs for a remote application.

Which of the following commands would BEST help the administrator accomplish this task?

dig

arp

show interface

hostname

13. A network technician is reviewing the interface counters on a router interface. The technician is attempting to confirm a cable issue.

Given the following information:

Which of the following metrics confirms there is a cabling issue?

Last cleared

Number of packets output

CRCs

Giants

Multicasts

14. Which of the following transceiver types can support up to 40Gbps?

SFP+

QSFP+

QSFP

SFP

15. Which of the following types of devices can provide content filtering and threat protection, and manage multiple IPSec site-to-site connections?

Layer 3 switch

VPN headend

Next-generation firewall

Proxy server

Intrusion prevention

16. The following configuration is applied to a DHCP server connected to a VPN concentrator:

There are 300 non-concurrent sales representatives who log in for one hour a day to upload reports, and 252 of these representatives are able to connect to the VPN without any Issues. The remaining sales representatives cannot connect to the VPN over the course of the day.

Which of the following can be done to resolve the issue without utilizing additional resources?

Decrease the lease duration

Reboot the DHCP server

Install a new VPN concentrator

Configure a new router

17. A network device is configured to send critical events to a syslog server; however, the following alerts are not being received:

Severity 5 LINK-UPDOWN: Interface 1/1, changed state to down

Severity 5 LINK-UPDOWN: Interface 1/3, changed state to down

Which of the following describes the reason why the events are not being received?

The network device is not configured to log that level to the syslog server

The network device was down and could not send the event

The syslog server is not compatible with the network device

The syslog server did not have the correct MIB loaded to receive the message

18. The network administrator is informed that a user’s email password is frequently hacked by brute-force programs.

Which of the following policies should the network administrator implements to BEST mitigate this issue? (Choose two.)

Captive portal

Two-factor authentication

Complex passwords

Geofencing

Role-based access

Explicit deny

19. A technician is connecting multiple switches to create a large network for a new office. The switches are unmanaged Layer 2 switches with multiple connections between each pair. The network is experiencing an extreme amount of latency.

Which of the following is MOST likely occurring?

Ethernet collisions

A DDoS attack

A broadcast storm

Routing loops

20. A network administrator redesigned the positioning of the APs to create adjacent areas of wireless coverage. After project validation, some users still report poor connectivity when their devices maintain an association to a distanced AP.

Which of the following should the network administrator check FIRST?

Validate the roaming settings on the APs and WLAN clients

Verify that the AP antenna type is correct for the new layout

Check to see if MU-MIMO was properly activated on the APs

Deactivate the 2.4GHz band on the APS

Page 3 of 12

21. Several WIFI users are reporting the inability to connect to the network. WLAN users on the guest network are able to access all network resources without any performance issues.

The following table summarizes the findings after a site survey of the area in question:

Which of the following should a wireless technician do NEXT to troubleshoot this issue?

Reconfigure the channels to reduce overlap

Replace the omni antennas with directional antennas

Update the SSIDs on all the APs

Decrease power in AP 3 and AP 4

22. A branch of a company recently switched to a new ISP. The network engineer was given a new IP range to assign.

The ISP assigned 196.26.4.0/26, and the branch gateway router now has the following configurations on the interface that peers to the ISP:

The network engineer observes that all users have lost Internet connectivity.

Which of the following describes the issue?

The incorrect subnet mask was configured

The incorrect gateway was configured

The incorrect IP address was configured

The incorrect interface was configured

23. Which of the following provides redundancy on a file server to ensure the server is still connected to a LAN even in the event of a port failure on a switch?

NIC teaming

Load balancer

RAID array

PDUs

24. A network administrator is configuring a load balancer for two systems.

Which of the following must the administrator configure to ensure connectivity during a failover?

VIP

NAT

APIPA

IPv6 tunneling

Broadcast IP

25. A network administrator is installing a wireless network at a client’s office.

Which of the following IEEE 802.11 standards would be BEST to use for multiple simultaneous client access?

CDMA

CSMA/CD

CSMA/CA

GSM

26. CORRECT TEXT

SIMULATION

You have been tasked with setting up a wireless network in an office. The network will consist of 3 Access Points and a single switch. The network must meet the following parameters:

The SSIDs need to be configured as CorpNet with a key of S3cr3t!

The wireless signals should not interfere with each other

The subnet the Access Points and switch are on should only support 30 devices maximum

The Access Points should be configured to only support TKIP clients at a maximum speed

INSTRUCTONS

Click on the wireless devices and review their information and adjust the settings of the access points to meet the given requirements.

If at any time you would like to bring back the initial state of the simulation, please click the Reset All button.

27. A user tries to ping 192.168.1.100 from the command prompt on the 192.168.2.101 network but gets the following response: U.U.U.U.

Which of the following needs to be configured for these networks to reach each other?

Network address translation

Default gateway

Loopback

Routing protocol

28. CORRECT TEXT

You are tasked with verifying the following requirements are met in order to ensure network security.

Requirements:

Datacenter

Ensure network is subnetted to allow all devices to communicate properly while minimizing address space usage

Provide a dedicated server to resolve IP addresses and hostnames correctly and handle port 53 traffic

Building A

Ensure network is subnetted to allow all devices to communicate properly while minimizing address space usage

Provide devices to support 5 additional different office users

Add an additional mobile user

Replace the Telnet server with a more secure solution

Screened subnet

Ensure network is subnetted to allow all devices to communicate properly while minimizing address space usage

Provide a server to handle external 80/443 traffic

Provide a server to handle port 20/21 traffic

INSTRUCTIONS

Drag and drop objects onto the appropriate locations. Objects can be used multiple times and not all placeholders need to be filled.

Available objects are located in both the Servers and Devices tabs of the Drag & Drop menu.

If at any time you would like to bring back the initial state of the simulation, please click the Reset All button.

29. A technician wants to deploy a new wireless network that comprises 30 WAPs installed throughout a three-story office building. All the APs will broadcast the same SSID for client access.

Which of the following BEST describes this deployment?

Extended service set

Basic service set

Unified service set

Independent basic service set

30. A technician is installing a high-density wireless network and wants to use an available frequency that supports the maximum number of channels to reduce interference.

Which of the following standard 802.11 frequency ranges should the technician look for while reviewing WAP specifications?

2.4GHz

5GHz

6GHz

900MHz

Page 4 of 12

31. Within the realm of network security, Zero Trust:

prevents attackers from moving laterally through a system.

allows a server to communicate with outside networks without a firewall.

block malicious software that is too new to be found in virus definitions.

stops infected files from being downloaded via websites.

32. Which of the following devices would be used to manage a corporate WLAN?

A wireless NAS

A wireless bridge

A wireless router

A wireless controller

33. A store owner would like to have secure wireless access available for both business equipment and patron use.

Which of the following features should be configured to allow different wireless access through the same equipment?

MIMO

TKIP

LTE

SSID

34. An engineer notices some late collisions on a half-duplex link. The engineer verifies that the devices on both ends of the connection are configured for half duplex.

Which of the following is the MOST likely cause of this issue?

The link is improperly terminated

One of the devices is misconfigured

The cable length is excessive

One of the devices has a hardware issue

35. A technician is troubleshooting a network switch that seems to stop responding to requests intermittently whenever the logging level is set for debugging.

Which of the following metrics should the technician check to begin troubleshooting the issue?

Audit logs

CPU utilization

CRC errors

Jitter

36. An IT director is setting up new disaster and HA policies for a company. Limited downtime is critical to operations. To meet corporate requirements, the director set up two different datacenters across the country that will stay current on data and applications. In the event of an outage, the company can immediately switch from one datacenter to another.

Which of the following does this BEST describe?

A warm site

Data mirroring

Multipathing

Load balancing

A hot site

37. A network engineer is investigating reports of poor network performance. Upon reviewing a report, the engineer finds that jitter at the office is greater than 10ms on the only WAN connection available.

Which of the following would be MOST affected by this statistic?

A VoIP sales call with a customer

An in-office video call with a coworker

Routing table from the ISP

Firewall CPU processing time

38. A technician is assisting a user who cannot connect to a network resource. The technician first checks for a link light.

According to troubleshooting methodology, this is an example of:

using a bottom-to-top approach.

establishing a plan of action.

documenting a finding.

questioning the obvious.

39. Which of the following can be used to centrally manage credentials for various types of administrative privileges on configured network devices?

SSO

TACACS+

Zero Trust

Separation of duties

Multifactor authentication

40. A technician is writing documentation regarding a company’s server farm. The technician needs to confirm the server name for all Linux servers.

Which of the following commands should the technician run?

ipconfig

nslookup

arp

route

Page 5 of 12

41. A network technician is manually configuring the network settings for a new device and is told the network block is 192.168.0.0/20.

Which of the following subnets should the technician use?

255.255.128.0

255.255.192.0

255.255.240.0

255.255.248.0

42. After the A record of a public website was updated, some visitors were unable to access the website.

Which of the following should be adjusted to address the issue?

TTL

TXT

SOA

43. A network administrator discovers that users in an adjacent building are connecting to the

company’s guest wireless network to download inappropriate material.

Which of the following can the administrator do to MOST easily mitigate this issue?

Reduce the wireless power levels

Adjust the wireless channels

Enable wireless client isolation

Enable wireless port security

44. According to troubleshooting methodology, which of the following should the technician do NEXT after determining the most likely probable cause of an issue?

Establish a plan of action to resolve the issue and identify potential effects

Verify full system functionality and, if applicable, implement preventive measures

Implement the solution or escalate as necessary

Test the theory to determine the cause

45. A user reports being unable to access network resources after making some changes in the office.

Which of the following should a network technician do FIRST?

Check the system’s IP address

Do a ping test against the servers

Reseat the cables into the back of the PC

Ask what changes were made

46. An administrator is writing a script to periodically log the IPv6 and MAC addresses of all the devices on a network segment.

Which of the following switch features will MOST likely be used to assist with this task?

Spanning Tree Protocol

Neighbor Discovery Protocol

Link Aggregation Control Protocol

Address Resolution Protocol

47. Branch users are experiencing issues with videoconferencing.

Which of the following will the company MOST likely configure to improve performance for these applications?

Link Aggregation Control Protocol

Dynamic routing

Quality of service

Network load balancer

Static IP addresses

48. Which of the following systems would MOST likely be found in a screened subnet?

RADIUS

FTP

SQL

LDAP

49. A network technician is installing new software on a Windows-based server in a different geographical location.

Which of the following would be BEST for the technician to use to perform this task?

RDP

SSH

FTP

DNS

50. A network engineer configured new firewalls with the correct configuration to be deployed to each remote branch. Unneeded services were disabled, and all firewall rules were applied successfully.

Which of the following should the network engineer perform NEXT to ensure all the firewalls are hardened successfully?

Ensure an implicit permit rule is enabled

Configure the log settings on the firewalls to the central syslog server

Update the firewalls with current firmware and software

Use the same complex passwords on all firewalls

Page 6 of 12

51. A technician is troubleshooting a wireless connectivity issue in a small office located in a high-rise building. Several APs are mounted in this office. The users report that the network connections frequently disconnect and reconnect throughout the day.

Which of the following is the MOST likely cause of this issue?

The AP association time is set too low

EIRP needs to be boosted

Channel overlap is occurring

The RSSI is misreported

52. Which of the following routing protocols is used to exchange route information between public autonomous systems?

OSPF

BGP

EGRIP

RIP

53. Client devices cannot enter a network, and the network administrator determines the DHCP scope is exhausted. The administrator wants to avoid creating a new DHCP pool.

Which of the following can the administrator perform to resolve the issue?

Install load balancers

Install more switches

Decrease the number of VLANs

Reduce the lease time

54. A network is experiencing a number of CRC errors during normal network communication.

At which of the following layers of the OSI model will the administrator MOST likely start to troubleshoot?

Layer 1

Layer 2

Layer 3

Layer 4

Layer 5

Layer 6

Layer 7

55. Which of the following is the physical topology for an Ethernet LAN?

Bus

Ring

Mesh

Star

56. A technician is installing multiple UPS units in a major retail store. The technician is required to keep track of all changes to new and old equipment.

Which of the following will allow the technician to record these changes?

Asset tags

A smart locker

An access control vestibule

A camera

57. Which of the following BEST describes a network appliance that warns of unapproved devices that are accessing the network?

Firewall

Proxy server

IDS

58. Access to a datacenter should be individually recorded by a card reader even when multiple employees enter the facility at the same time.

Which of the following allows the enforcement of this policy?

Motion detection

Access control vestibules

Smart lockers

Cameras

59. A technician is installing a cable modem in a SOHO.

Which of the following cable types will the technician MOST likely use to connect a modem to the ISP?

Coaxial

Single-mode fiber

Cat 6e

Multimode fiber

60. Given the following information:

Which of the following command-line tools would generate this output?

netstat

arp

dig

tracert

Page 7 of 12

61. A technician is configuring a network switch to be used in a publicly accessible location.

Which of the following should the technician configure on the switch to prevent unintended connections?

DHCP snooping

Geofencing

Port security

Secure SNMP

62. Which of the following would need to be configured to ensure a device with a specific MAC address is always assigned the same IP address from DHCP?

Scope options

Reservation

Dynamic assignment

Exclusion

Static assignment

63. Which of the following DNS records works as an alias to another record?

AAAA

CNAME

SOA

64. Which of the following TCP ports is used by the Windows OS for file sharing?

389

445

1433

65. A technician is searching for a device that is connected to the network and has the device’s physical network address.

Which of the following should the technician review on the switch to locate the device’s network port?

IP route table

VLAN tag

MAC table

QoS tag

66. Which of the following service models would MOST likely be used to replace on-premises servers with a cloud solution?

PaaS

IaaS

SaaS

Disaster recovery as a Service (DRaaS)

67. A fiber link connecting two campus networks is broken.

Which of the following tools should an engineer use to detect the exact break point of the fiber link?

OTDR

Tone generator

Fusion splicer

Cable tester

PoE injector

68. Which of the following would MOST likely be used to review previous upgrades to a system?

Business continuity plan

Change management

System life cycle

Standard operating procedures

69. A network administrator is implementing OSPF on all of a company’s network devices.

Which of the following will MOST likely replace all the company’s hubs?

A Layer 3 switch

A proxy server

A NGFW

A WLAN controller

70. Wireless users are reporting intermittent internet connectivity. Connectivity is restored when the users disconnect and reconnect, utilizing the web authentication process each time. The network administrator can see the devices connected to the APs at all times.

Which of the following steps will MOST likely determine the cause of the issue?

Verify the session time-out configuration on the captive portal settings

Check for encryption protocol mismatch on the client’s wireless settings

Confirm that a valid passphrase is being used during the web authentication

Investigate for a client’s disassociation caused by an evil twin AP

Page 8 of 12

71. Which of the following ports is commonly used by VoIP phones?

143

445

5060

72. A network technician needs to ensure outside users are unable to telnet into any of the servers at the datacenter.

Which of the following ports should be blocked when checking firewall configuration?

3389

8080

73. Which of the following factors should be considered when evaluating a firewall to protect a datacenter’s east-west traffic?

Replication traffic between an on-premises server and a remote backup facility

Traffic between VMs running on different hosts

Concurrent connections generated by Internet DDoS attacks

VPN traffic from remote offices to the datacenter’s VMs

74. Which of the following is the LARGEST MTU for a standard Ethernet frame?

1452

1492

1500

2304

75. The management team needs to ensure unnecessary modifications to the corporate network are not permitted and version control is maintained.

Which of the following documents would BEST support this?

An incident response plan

A business continuity plan

A change management policy

An acceptable use policy

76. A workstation is configured with the following network details:

Software on the workstation needs to send a query to the local subnet broadcast address.

To which of the following addresses should the software be configured to send the query?

10.1.2.0

10.1.2.1

10.1.2.23

10.1.2.255

10.1.2.31

77. A network engineer performs the following tasks to increase server bandwidth:

Connects two network cables from the server to a switch stack

Configure LACP on the switchports

Verifies the correct configurations on the switch interfaces

Which of the following needs to be configured on the server?

Load balancing

Multipathing

NIC teaming

Clustering

78. An engineer is configuring redundant network links between switches.

Which of the following should the engineer enable to prevent network stability issues?

802.1Q

STP

Flow control

CSMA/CD

79. A website administrator is concerned the company’s static website could be defaced by hacktivists or used as a pivot point to attack internal systems.

Which of the following should a network security administrator

recommend to assist with detecting these activities?

Implement file integrity monitoring.

Change the default credentials.

Use SSL encryption.

Update the web-server software.

80. At which of the following OSI model layers would a technician find an IP header?

Layer 1

Layer 2

Layer 3

Layer 4

Page 9 of 12

81. Which of the following is used to prioritize Internet usage per application and per user on the network?

Bandwidth management

Load balance routing

Border Gateway Protocol

Administrative distance

82. A network engineer is investigating reports of poor network performance. Upon reviewing a device configuration, the engineer finds that duplex settings are mismatched on both ends.

Which of the following would be the MOST likely result of this finding?

Increased CRC errors

Increased giants and runts

Increased switching loops

Increased device temperature

83. A technician receives feedback that some users are experiencing high amounts of jitter while using the wireless network. While troubleshooting the network, the technician uses the ping command with the IP address of the default gateway and verifies large variations in latency. The technician thinks the issue may be interference from other networks and non-802.11 devices.

Which of the following tools should the technician use to troubleshoot the issue?

NetFlow analyzer

Bandwidth analyzer

Protocol analyzer

Spectrum analyzer

84. A company built a new building at its headquarters location. The new building is connected to the company’s LAN via fiber-optic cable. Multiple users in the new building are unable to access the company’s intranet site via their web browser, but they are able to access internet sites.

Which of the following describes how the network administrator can resolve this issue?

Correct the DNS server entries in the DHCP scope

Correct the external firewall gateway address

Correct the NTP server settings on the clients

Correct a TFTP Issue on the company’s server

85. A company hired a technician to find all the devices connected within a network.

Which of the following software tools would BEST assist the technician in completing this task?

IP scanner

Terminal emulator

NetFlow analyzer

Port scanner

86. An attacker is attempting to find the password to a network by inputting common words and phrases in plaintext to the password prompt.

Which of the following attack types BEST describes this action?

Pass-the-hash attack

Rainbow table attack

Brute-force attack

Dictionary attack

87. A client recently added 100 users who are using VMs. All users have since reported slow or unresponsive desktops. Reports show minimal network congestion, zero packet loss, and acceptable packet delay.

Which of the following metrics will MOST accurately show the underlying performance issues? (Choose two.)

CPU usage

Memory

Temperature

Bandwidth

Latency

Jitter

88. Which of the following is MOST likely to generate significant East-West traffic in a datacenter?

A backup of a large video presentation to cloud storage for archival purposes

A duplication of a hosted virtual server to another physical server for redundancy

A download of navigation data to a portable device for offline access

A query from an IoT device to a cloud-hosted server for a firmware update

89. A technician is deploying a new switch model and would like to add it to the existing network monitoring software. The technician wants to know what metrics can be gathered from a given switch.

Which of the following should the technician utilize for the switch?

MIB

Trap

Syslog

Audit log

90. A network administrator needs to implement an HDMI over IP solution.

Which of the following will the network administrator MOST likely use to ensure smooth video delivery?

Link aggregation control

Port tagging

Jumbo frames

Media access control

Page 10 of 12

91. Which of the following services can provide data storage, hardware options, and scalability to a third-party company that cannot afford new devices?

SaaS

IaaS

PaaS

DaaS

92. A company wants to implement a large number of WAPs throughout its building and allow users to be able to move around the building without dropping their connections.

Which of the following pieces of equipment would be able to handle this requirement?

A VPN concentrator

A load balancer

A wireless controller

A RADIUS server

93. A network technician is configuring a new firewall for a company with the necessary access requirements to be allowed through the firewall.

Which of the following would normally be applied as the LAST rule in the firewall?

Secure SNMP

Port security

Implicit deny

DHCP snooping

94. Which of the following is required when connecting an endpoint device with an RJ45 port to a network device with an ST port?

A media converter

A bridge

An MDIX

A load balancer

95. A rogue AP was found plugged in and providing Internet access to employees in the break room.

Which of the following would be BEST to use to stop this from happening without physically removing the WAP?

Password complexity

Port security

Wireless client isolation

Secure SNMP

96. Allow devices to move to different switchports on the same VLAN

Which of the following should the network administrator do to accomplish these requirements?

Set up a reservation for each device

Configure a static IP on each device

Implement private VLANs for each device

Use DHCP exclusions to address each device

97. Which of the following is MOST commonly used to address CVEs on network equipment and/or operating systems?

Vulnerability assessment

Factory reset

Firmware update

Screened subnet

98. A systems administrator is configuring a firewall using NAT with PAT.

Which of the following would be BEST suited for the LAN interface?

172.15.0.0/18

172.18.0.0/10

172.23.0.0/16

172.28.0.0/8

172.32.0.0/14

99. A network administrator is configuring a database server and would like to ensure the database engine is listening on a certain port.

Which of the following commands should the administrator use to accomplish this goal?

nslookup

netstat -a

ipconfig /a

arp -a

100. A network technician has multimode fiber optic cable available in an existing IDF.

Which of the following Ethernet standards should the technician use to connect the network switch to the existing fiber?

10GBaseT

1000BaseT

1000BaseSX

1000BaseLX

Page 11 of 12

101. A technician is troubleshooting a workstation's network connectivity and wants to confirm which switchport corresponds to the wall jack the PC is using.

Which of the following concepts would BEST help the technician?

Consistent labeling

Change management

Standard work instructions

Inventory management

Network baseline

102. Which of the following is used to provide networking capability for VMs at Layer 2 of the OSI model?

VPN

VRRP

vSwitch

VIP

103. Given the following output:

Which of the following attacks is this MOST likely an example of?

ARP poisoning

VLAN hopping

Rogue access point

Amplified DoS

104. A network technician needs to correlate security events to analyze a suspected intrusion.

Which of the following should the technician use?

SNMP

Log review

Vulnerability scanning

SIEM

105. Must be vendor neutral

Which of the following methods should the engineer select?

TWP-RC4

CCMP-AES

EAP-TLS

WPA2

106. Which of the following protocols will a security appliance that is correlating network events from multiple devices MOST likely rely on to receive event messages?

Syslog

Session Initiation Protocol

Secure File Transfer Protocol

Server Message Block

107. A network administrator has been directed to present the network alerts from the past week to the company's executive staff.

Which of the following will provide the BEST collection and presentation of this data?

A port scan printout

A consolidated report of various network devices

A report from the SIEM tool

A report from a vulnerability scan done yesterday

108. Which of the following is the physical security mechanism that would MOST likely be used to enter a secure site?

A landing page

An access control vestibule

A smart locker

A firewall

109. A network administrator wants to improve the security of the management console on the company's switches and ensure configuration changes made can be correlated to the administrator who conformed them.

Which of the following should the network administrator implement?

Port security

Local authentication

TACACS+

Access control list

110. Which of the following cable types would MOST likely be used to provide high-speed network connectivity between nearby buildings?

UTP

Coaxial

Fiber

Cat 5

Twinaxial

Page 12 of 12

111. Which of the following attacks encrypts user data and requires a proper backup implementation to recover?

DDoS

Phishing

Ransomware

MAC spoofing

112. A network administrator wants to analyze attacks directed toward the company's network.

Which of the following must the network administrator implement to assist in this goal?

A honeypot

Network segmentation

Antivirus

A screened subnet

113. A network administrator wants to reduce overhead and increase efficiency on a SAN.

Which of the following can be configured to achieve these goals?

Port aggregation

Traffic shaping

Jumbo frames

Flow control

114. A SaaS provider has decided to leave an unpatched VM available via a public DMZ port.

With which of the following concepts is this technique MOST closely associated?

Insider threat

War driving

Evil twin

Honeypot

115. A city has hired a new employee who needs to be able to work when traveling at home and at the municipal sourcing of a neighboring city that snares services. The employee is issued a laptop, and a technician needs to train the employee on the appropriate solutions for secure access to the network from all the possible locations.

On which of the following solutions would the technician MOST likely train the employee?

Site-to-site VPNs between the two city locations and client-to-site software on the employee's laptop tor all other remote access

Client-to-site VPNs between the travel locations and site-to-site software on the employee's laptop for all other remote access

Client-to-site VPNs between the two city locations and site-to-site software on the employee's laptop for all other remote access

Site-to-site VPNs between the home and city locations and site-to-site software on the employee's laptop for all other remote access

116. A corporation has a critical system that would cause unrecoverable damage to the brand if it was taken offline.

Which of the following disaster recovery solutions should the corporation implement?

Full backups

Load balancing

Hot site

Snapshots

117. A firewall administrator is implementing a rule that directs HTTP traffic to an internal server listening on a non-standard socket.

Which of the following types of rules is the administrator implementing?

NAT

PAT

STP

SNAT

ARP

Comments (12)

Troy Lockhart July 16, 2024 Reply

hello I purchased the premium n10-008 and I still cannot get my file to import to the ICE simulator
- dumps July 16, 2024 Reply
  
  Hi, I just checked your order. You did not purchased the ice file, you only purchased pdf. If you need the software version (.ice file), you need to purchase it.
Bo November 26, 2023 Reply

Hi

How can i purchase Network+ N10-008?
- dumps November 26, 2023 Reply
  
  Hi, you can purchase it with the following link: https://www.itfreedumps.com/exam/real-uncategorized-product-you-need-dumps/
Pooch August 28, 2023 Reply

Hi I want to write the exam so if I buy the dumps before end of August how long will it expire when September begins?
- dumps August 28, 2023 Reply
  
  Hi, the N10-008 exam dumps are valid now.
Prakash Dhungana June 24, 2023 Reply

I loved your Free Dumps but i want to get my CompTIA Network+ Certification please let me know what should i do next process.
- dumps June 24, 2023 Reply
  
  Hi, you can use the following linke to purchase N10-008 exam dumps: https://www.itfreedumps.com/exam/real-uncategorized-product-you-need-dumps/
  and then we can send you the dumps.
  - Norman November 8, 2023 Reply
    
    Hi,
    
    I’m confused what you sent the link to is called “Real Uncategorized Product you need Dumps” how do I convert that into the N10-008 questions?
    - dumps November 9, 2023 Reply
      
      Hi, after you complete the payment, we can help change the product into N10-008 questions.
Hello February 3, 2023 Reply

Hello
- dumps February 4, 2023 Reply
  
  Hi, what can I do for u?

Good Updated Questions for CompTIA Network+ N10-008 Test

Good Updated Questions for CompTIA Network+ N10-008 Test

Share this post

Comments (12)

Leave a Reply Cancel reply

Related Posts