Great HPE6-A72 Aruba Certified Switching Associate Exam Dumps

dumps2021-08-14T03:21:21+08:00

HPE6-A72 Aruba Certified Switching Associate Exam is easy for the HP candidates to pass now. We collected all the related great dumps for HP certification HPE6-A72 exam, which can help you save much time and energy. We all know that HPE6-A72 exam is for IT Professionals who are new to deploying SMB solutions based on HPE Aruba products and technologies.

Learning HP certification HPE6-A72 exam basic information is also useful in your preparation. There are 60 questions in real HP HPE6-A72 exam, and you have 1 hour 30 minutes to complete all the questions. The required passing score of HP HPE6-A72 exam is 75%. The test languages are Latin American Spanish, Japanese, English.

We provide free online great HPE6-A72 Aruba Certified Switching Associate Exam dumps below, which can help you test the following objectives: Identify, describe, and apply foundational networking architectures and technologies, Identify, describe, and differentiate the functions and features of Aruba products and solutions, and so on.

Page 1 of 2

1. DRAG DROP

Place the OSI Layers in the correct order. Arrange them from least to greatest, starting with Layer 1 on the top, and progressing to Layer 7 on the bottom.

2. Which two options are the Layer 2 protocols? (Choose two.)

802.1Q

IPSec

STP

RIP

802.11af

3. What are two methods for remotely managing an Aruba AOS-CX switch? (Choose two.)

SNMPv2c

HTTPS

USB-C console

Telnet

SSH

4. Core(config)# user admin password

Core(config)# interface mgmt

Core(config-if-mgmt)# ip static 10.254.16.89/22

Core(config-if-mgmt)# default-gateway 10.254.19.129

Core(config)# ssh server vrf mgmt

Core(config)# https-server vrf mgmt

You are tasked with configuring the Core switch to be managed by NetEdit. Currently, the Core switch is at factory-default settings.

Which two steps are missing? (Choose two.)

Core(config)# https-server rest access-mode read-write

Core(config-if-mgmt)# no shutdown

Core(config-if-mgmt)# no tftp-server

Core(config-if-mgmt)# enable

Core(config)# https-server rest access-mode read-only

5. Which field in the IPv4 header indicates whether the IP packet carries TCP or UDP traffic?

Protocol

IHL

TTL

Identification

6. Which network category applies to a SOHO internal network?

SD-WAN

LAN

WAN

Internet

7. Core# configure terminal

Core(config)# vrf Green

Core(config-vrf)# exit

Core(config)#

Core(config)# interface vlan 50

Core(config-if-vlan)# ?

Given the configuration on the CORE switch shown above, what command would follow to assign the switched virtual interface (SVI) vlan 50 to the VRF created?

Core(config-if-vlan)# vrf attach Green

Core(config-if-vlan)# ip vpn-instance Green

Core(config-if-vlan)# ip vrf forwarding Green

Core(config-if-vlan)# routing-context Green vrf

8. Which Ethernet port combination does the Aruba 5400R ZL2 switch series support?

10/100 Megabit Ethernet, Gigabit Ethernet, and 100 Gigabit Ethernet

Gigabit Ethernet, 25 Gigabit Ethernet, and 40 Gigabit Ethernet

10/100 Megabit Ethernet, Gigabit Ethernet, 25 Gigabit Ethernet, and 100 Gigabit Ethernet

10/100 Megabit Ethernet, Gigabit Ethernet, and 40 Gigabit Ethernet

9. Refer to the exhibit.

What is the correct binary conversion of the last two hexadecimal characters of the physical address?

1101 1000

1110 1101

1001 1111 0101 0011

1000 1101 1110 1101

10. Which command can be used to find the serial number of an Aruba OS-CX switch?

The command inventory

The command version

The command show running-configuration

The command show system

11. What is the login and password combination is used when first configuring an Aruba OS-CX switch from factory defaults?

12. What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

copy running-config checkpoint startup-config

copy startup-config running-config

copy running-config initial-checkpoint

copy running-config default

13. Refer to the exhibit.

What configuration is needed in order for "show LLDP configuration" to show this output?

none; LLDP is enabled by default on Aruba switches

configuring LLDP both globally and on the interfaces

enabling LLDP on the interfaces only

configuring LLDP globally only

14. Which two commands will save the running-config so that changes will be loaded automatically on the next reboot? (Choose two.)

write memory

save

copy config config1 config startup-config

copy running-config startup-config

copy running-config checkpoint boot-config

15. Which two statements accurately describe stacking with Aruba switches? (Choose two.)

A VSF stack is allowed between an AOS-CX 6300M and 6300F switches.

VSF is a core or aggregation layer stacking technology due to the high resiliency of sharing a single control plane.

The VSF feature is not compatible between AOS-CX and AOS platforms.

A VSF stack is allowed between an AOS 5400R and an AOS-CX 6400.

VSF and VSX are stacking option with the AOS-CX 8320. 8325. 8400. and 6400 models.

16. What is the correct description of a Multi-Layer Switch?

a switch with Layer 3 routing capabilities but lacks any Layer 1 features as a consequence

any switch that supports PoE, LLDP-MED and Flow Control

has all the functionality of a Layer 2 switch and most of the functionality of a Layer 3 router

multi-Layer refers specifically to using chassis switches with several line cards over stack port switches

17. Refer to the exhibit.

Which command produces the above output?

show interface port 1/1/10 trunk

show vlan port 1/1/10

show trunk port 1/1/10 extended

show interface port 1/1/10 switchport

18. Which command will suppress LLDP messages from egressing on a given port while still allowing LLDP to be enabled on the switch?

switch(config-if)# no lldp interface (port) transmit

switch(config-if)# no lldp transmit

switch(config-if)# no lldp receive

switch(config)# no lldp

19. HOTSPOT

Click on the colored box that corresponds with the line that best represents Unicast traffic flow.

20. Which two port characteristics must match between LAG interfaces? (Choose two.)

Port number

Duplex

Member ID

Media type

Chassis number

Page 2 of 2

21. DRAG DROP

Match each network protocol to the correct server listening port. Not all answers will be used.

22. HOTSPOT

Review the exhibit.

As the frame traverses from **PC-1** to **Server-1**, the VLAN tag will be removed.

Click on the interface (circled in green) where the VLAN tag will be removed.

23. Refer to the exhibit.

What command will display the debug l2mac events?

show module L2MAC

show debug terminal

show debug buffer module L2MAC

show debug all

24. Refer to the exhibit.

The above command was applied to an Aruba AOS-CX 6300M 24-port switch with 4-port SFP56 uplinks. All ports are set as access switchports.

Which ports carry VLAN 1 traffic?

1/1/8, 1/1/10, 1/1/5-1/1/24

1/1/1-1/1/28

1/1/1-1/1/24

1/1/8-1/1/10, 1/1/5-1/1/28

25. Refer to the exhibit.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.

What is a valid configuration for Access-2 to join the VSF stack?

Access-2# configure Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

Access-2# configure Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2 This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

26. What are two primary concerns regarding layer two loops in a redundant topology? (Choose two.)

routing loops

costs associated with upgrading from copper to fiber

multiple frame copies leading to instability of the MAC address table

security issues with a redundant loop indicating to hackers that a back-door exists

broadcast storms

27. Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

UDP 1812 and UDP 1813

UDP 161

TCP 443

UDP 162

28. Refer to the exhibit.

Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.

Which configuration will correct the issue?

Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181

Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181

Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.1

Host-B: assign the default-gateway address 10.1.20.181

29. DRAG DROP

Match the term to the correct description.

30. What is Deep Packet Inspection?

a machine learning method of packet inspection for the purpose of choosing which dynamic routing protocol to automatically assign

a concept that applies to firewalls, when examining packets only up through Layer 4

a function of Policy Based Routing that examines the entire IPv4 header to forward traffic based on factors other than destination address

a firewall process of examining the packet header all the way to Layer 7 in order to determine if the packet should be permitted or denied

31. What is the binary conversion of the hexadecimal value 0x2001?

0010 0001

0002 0000 0000 0001

0011 0000 0000 0001

0010 0000 0000 0001

32. You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.

What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?

checkpoint rollback 10

checkpoint auto 10

checkpoint auto confirm 10

boot system secondary 10

33. The following command is issued:

Switch# checkpoint rollback start

What is the result?

The command will fail because rollback commands must be issued from global-config mode.

The switch will revert the running-configuration to the checkpoint called 'start1 without a reboot.

The command will fail because it is incomplete.

The switch will use the checkpoint 'rollback1 as the starting configuration on next reboot.

34. Refer to the exhibit.

The above output is the result of issuing the command show system resource-utilization.

What command should be used to enable terminal output line by line or page by page?

The command page

The command terminal length 30

The command more

The command less

Great HPE6-A72 Aruba Certified Switching Associate Exam Dumps

Great HPE6-A72 Aruba Certified Switching Associate Exam Dumps

Share this post

Leave a Reply Cancel reply

Related Posts