D-PST-MN-A-24 PowerStore Maintenance Exam Free Dumps

dumps2024-04-30T09:15:20+08:00

D-PST-MN-A-24 PowerStore Maintenance exam consists of 60 questions, and you have 90 minutes to answer all the questions. The required passing score for the D-PST-MN-A-24 exam is 63%. We provide the latest D-PST-MN-A-24 PowerStore Maintenance exam dumps, which are the best material for you to pass the test and get certified. Free PowerStore Maintenance D-PST-MN-A-24 exam dumps are available below.

Page 1 of 6

1. How many nodes are in the base enclosure?

2 nodes configured as Active-Standby

1 node with duel connectivity

1 node with high availability enabled

2 nodes configured as Active-Active

2. Which formats are available to list alerts?

Standard, NVP, CSV and JSON

Table, XLS, CSV and JSON

Table, NVP, CSV and XLS

Table, NVP, CSV and JSON

3. Refer to the exhibit.

EMC-DES-12413_1

What is the result of the network configuration show for a Dell EMC PowerStore T node A management port?

VLAN 1 and VLAN 1501 pass tagged traffic

VLAN 1 passes tagged traffic, VLAN 1501 passes untagged traffic

VLAN 1 passes untagged traffic, VLAN 1501 passes tagged traffic

VLAN 1 and VLAN 1501 pass untagged traffic

4. Refer to the exhibit.

DES-1241 85_2

A Storage Administrator noticed a solid amber LED.

What does this mean?

Drive identification on

Drive rebuilding

Power up

Drive faulted

5. How is a defective embedded module displayed in Dell EMC PowerStore Manager?

Orange with an empty state

Orange with a faulted state

Blue with a faulted state

Blue with an empty state

6. Which LED combination shows a connected and working node?

power LED: steady green fault LED: amber

power LED: blinking green fault LED: off

power LED: blinking green fault LED: blue

power: LED: steady green fault LED: off

7. What is the maximum number of base enclosures in a cluster when planning a Dell EMC PowerStore T installation?

8. What is the last step when adding a drive to a Dell EMC PowerStore system?

Verify the new drive is seen

Add the drive to the pool

Backup the keystore

Zero the drive

9. What is a step in configuring the ToR data switches for a Dell EMC PowerStore T?

Configure a port for the discovery laptop

Create VLANs for NAS servers

Create VLAN for vMotion networks

Configure ports for management on native VLAN

10. What describes the ICM and ICD networks?

Address type is dynamic and automatically reconfigured on discovery results

They are NOT encrypted

Address type is persistent throughout the life of the cluster and CANNOT to be modified

They are encrypted with IPsec

Page 2 of 6

11. Through which network do external hosts connect to the cluster for data access?

Management

ICM

ICD

Storage

12. Refer to the exhibit.

DES-1241 87_1

What is indicated when the circled LED on the base enclosure is illuminated amber?

Base enclosure power-on

Cluster discovery state

Cluster service mode

Base enclosure fault

13. Refer to the exhibit.

DES-1241 83_1

A Storage Administrator is troubleshooting a Dell EMC PowerStore T hardware issue. They observe that the base enclosure LED circled is blue.

What does this indicate?

Base enclosure hardware is operating normally

Base enclosure has a component hardware fault

Cluster has only a single appliance

Appliance has a node in service mode

14. Which network is used for internal communication?

Intra-Cluster Data

Intra-Cluster Management

NAD Network

Inter-Node Network

15. DRAG DROP

Order the NDU operational steps.

EMC-DES-12418_1

16. A Storage Administrator notices two fans in a Dell EMC PowerStore are faulted.

What describes the system behavior in this circumstance?

A five-minute timer starts upon the second fan fault and the system shuts down automatically after the timer expires

CPU clock speed is reduced by 50% to lower internal temperatures and the system continues normal operations

An increased fan speed signal is sent to the surviving fans and the system continues normal operations

Upon the second fan fault, all host I/O is terminated immediately and the PowerStore goes through the halt and vault process and shuts down

17. What does the command “svc_journalctl -f -g “st_io_monitor”” do?

Retrieves log messages from the specified error and watches for re-occurrence

Ignores log messages from the specified error and re-occurring errors

Rotates the log based on the specified error

Deletes all logs before the specified error

18. A Storage Administrator notices a Critical alert present in Dell EMC PowerStore Manager relating to data integrity.

What action within the alert details slide-out panel is helpful in troubleshooting the problem?

Select the Gather Support Materials from Service and Support

Access the Repair Flow link to schedule a support engagement

Examine Notifications to obtain a list of corrective actions

Re-engage support through previous listed Related Events

19. Which option is used when running the journalctl command to query log messages regardless of capitalization?

option --casesensitive=YES/NO

option -quotes

option -ignorecase

option --casesensitive=TRUE/FALSE

20. Which Dell EMC PowerStore network uses an appliance backplane?

ICD

MPIO

Inter-node

Inter-cluster management

Page 3 of 6

21. What describes the power requirements for Dell EMC PowerStore?

Lower model numbered systems require less AC line current than higher model numbered systems

T models require less total power than X models

X models require less total power than T models

Lower model numbered systems require less input voltage (VAC) than higher model numbered systems

22. What Dell EMC PowerStore reference provides the user access to the entire set of product documentation, knowledge base articles, and product warranty and contracts?

SolVe Desktop and Online

Dell EMC Online Support

Dell EMC PowerStore Series Product Page

PowerStore Manager in App (Offline) Help

23. DRAG DROP

Match the base enclosure SAS ports in column A to their corresponding expansion LCC ports in column B; when connecting a PowerStore base enclosure to a single expansion enclosure.

EMC-DES-124111_1

24. What describes Dell EMC PowerStore X power down?

PowerStore X node, appliance, or cluster power down is done entirely with vCenter server commands

Powering down a PowerStore X node, appliance, or cluster is done in the same manner as a PowerStore T

PowerStore X node, appliance, or cluster power down utilizes the VSi plugin to perform the needed vCenter server operations

Powering down a PowerStore X node, appliance, or cluster requires additional vCenter server commands

25. DRAG DROP

When connecting a PowerStore base enclosure to 2 expansion enclosures, match the base SAS ports in column A to their corresponding expansion LCC ports in column B.

未标题-1

26. While on-site installing a Dell EMC PowerStore system, the node A and embedded module fault LEDs are alternating blue and amber (blue for 3 seconds).

What does this indicate?

The system is booting

Nodes are in service mode

The system is not initialized

Nodes are in degraded mode

27. From where can a data collection be initiated within Dell EMC PowerStore Manager?

Appliance, node, and storage resource

Cluster, appliance, and alerts

Cluster, appliance, and event log

Node, storage resource, and alerts

28. What safety equipment is critical to have on hand to avoid equipment failure before replacing any components in a Dell EMC PowerStore array?

Maintenance Kit

ESD Kit

Stabilization Kit

Rail Kit

29. How can the PUHC health check results be viewed?

By accessing the Swagger UI

From syslog server

In Details of Appliances and Nodes

From management DB

30. When a Dell EMC PowerStore node powers up in service mode, what are the commands and sequence used from the appliance SSH client to restore the node back to normal?

svc_rescue_state clear svc_node reboot

svc_node restart svc_rescue_state start

svc_rescue_state normal svc_node start

svc_node shutdown svc_rescue_state clear

Page 4 of 6

31. A Storage Administrator needs to address specific fixes within their Dell EMC PowerStore system.

Which NDU software upgrade option is used for this situation?

Hotfixes

vCenter

Drive firmware

Software releases

32. What is the default log collection schedule?

Weekly

As scheduled during install

Hourly

Daily

33. Refer to the exhibit.

图片包含游戏机

描述已自动生成

What is indicated when the circled LED on an expansion enclosure is illuminated amber?

Expansion enclosure faulted

SAS bus link up

SAS bus link down

Expansion enclosure power-on

34. Which component is only replaceable by qualified personnel?

Battery backup unit

Embedded I/O module

Memory module

4-Port mezzanine card

35. Refer to the exhibit.

DES-1241 811_1

What type of cable is used for the ToR switch configuration shown for the S5248F-ON switches?

10 GigE Cat 6 Ethernet RJ-45

25 GigE Twinax

100 GigE QSFP28

10 GigE SFP optical cable

36. What is an alternative way to collect logs instead of using the Dell EMC PowerStore manager GUI?

Data Collect using Service Container

USB stick inserted into the system

Data Collect using vCenter

Discovery Utility

37. What are the recommended number of network switches in a Dell EMC PowerStore T environment?

38. A Storage Administrator has an existing single appliance Dell EMC PowerStore 3000T cluster. An additional PowerStore 9000T has been purchased to add into the existing cluster.

How does the administrator proceed?

Additional VLTi links on the ToR switching must be configured for the 9000T to support the increased inter-switch network load

Add the new 9000T appliance into the cluster per the procedure; mixed models of the same type are supported

Remove two of the four NVMe NVRAM drives from the 9000T the caching configuration of all clustered appliances must match

The new appliance cannot be added to the cluster; appliance model and type must match when clustering appliances together

39. What describes the SAS cabling when adding an expansion enclosure to a Dell EMC PowerStore, for each node and expansion enclosure side?

SAS cabling goes from existing A ports to new ports. At the last enclosure, SAS cabling returns from the A ports to the originating node’s B ports

SAS cabling goes from existing A ports to new ports. At the last enclosure, SAS cabling returns from the A ports to the alternate node’s ports

SAS cabling goes from existing ports to new A ports. At the last enclosure, SAS cabling returns from the ports to the alternate node’s A ports

SAS cabling goes from existing ports to new A ports. At the last enclosure, SAS cabling returns from the ports to the originating node’s A ports

40. During an emergency event an ESD-Kit is unavailable for FRU replacement.

How can the work proceed?

If FRU does not contain ESD-Kit, continue without it

Order “Emergency ESD-Kit” ASAP

Follow precautions described in the “Emergency Procedure”

Use package material to build “provisional ESD-Kit”

Page 5 of 6

41. A Storage Administrator has just installed PSTCLI on a Linux client. The administrator is unfamiliar with the PSTCLI command list.

How can the administrator get a list of all PSTCLI commands from the cli> prompt?

Type the <Ctrl>+keys together

Press the <Tab> key

Use the show all command

Use the help all command

42. A Storage Administrator needs to add drives to a base enclosure of a Dell EMC PowerStore 7000T system. The system currently contains 10 750 GB NVMe SCM drives.

Which drive configuration maximizes the base enclosure capacity?

11 15360 GB NVMe SSD drives in slots 10 - 20

13 15360 GB NVMe SSD drives in slots 10 - 22

11 750 GB NVMe SCM drives in slots 10 - 20

13 750 GB NVMe SCM drives in slots 10 - 22

43. What is the maximum number of expansion enclosures that a single Dell EMC PowerStore appliance supports?

44. What describes Dell EMC PowerStore X front-end cabling?

Uses internal VMware virtual switching and does not require a management network

Storage and management use the same LACP bonded cable connection

Uses VLTi data switch interconnectivity to support vMotion networks

Management and discovery use the same cables and connections as storage

45. A Storage Administrator wants to upgrade a two appliance Dell EMC PowerStore cluster.

Which Commit options need to be chosen to have all appliances upgraded in the last step?

Appliance, Cluster

Appliance, Appliance

Cluster, Appliance

Cluster, Cluster

46. What method is used to power down a Dell EMC PowerStore system in a true emergency situation?

Run svc_node shutdown

Power Down Cluster in PowerStore GUI

Turn off the cabinet switches

Remove base enclosure power cables

47. How is a service laptop IP configured to connect to the Service LAN port of a Dell EMC PowerStore node?

Static IP: 128.221.1.249 and netmask: 255.255.255.0

Obtain IP address from DHCP on PowerStore

Static IP: 169.254.1.249 and netmask: 255.0.0.0

Leave IP address and netmask unconfigured

48. Which reference source provides service information and FRU procedures for the Dell EMC PowerStore?

SolVe Tool

Dell EMC PowerStore Product Page

PowerStore Manager help

DELL EMC Online Support

49. A Storage Administrator ran a PSTCLI command on a Linux host. The error " -bash: pstcli: command not found" appears.

How is the problem resolved?

Add the installation directory to the PATH variable on shell initialization file

Install in default directory /opt/dellemc/pstcli-version/bin/

Add /opt/dellemc/pstcli/bin/in PSTCL

Run rpm -ihv pstcli to reinstall the PSTCLI software on the Linux host

50. A Storage Administrator is adding an appliance into an existing Dell EMC PowerStore T cluster.

What is different about the management network configuration for the new appliance compared to configuring an initial appliance for the cluster?

All the needed management IP addresses for the new appliance must be pre-configured on the cluster

Additional appliance does not require a cluster management IP address

Additional appliance inherits all its management IPs from the existing appliance

All the needed management IP addresses for the new appliance are auto-generated by the cluster

Page 6 of 6

51. Which number in the code-naming schema represents a beta distribution?

52. Refer to the exhibit.

DES-1241 816_1

A Storage Administrator noticed a drive LED blinking blue.

What does this indicate?

Is faulted

Access activity

Power up

Identification is on

53. A Storage Administrator needs to connect through SSH to run svc commands.

How is the SSH session configured?

Appliance IP address using port 22

NAS server IP address using port 26

NAS server IP address using port 22

Appliance IP address using port 26

D-PST-MN-A-24 PowerStore Maintenance Exam Free Dumps

D-PST-MN-A-24 PowerStore Maintenance Exam Free Dumps

Share this post

Leave a Reply Cancel reply

Related Posts